Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
SERVICE AND MAINTENANCE SAFETY Stop engine, set brake, remove ignition key, and wait for all moving parts to stop before servicing, adjusting, repairing, or unplugging. Support the equipment with blocks or safety stands before working beneath it. Follow good shop practices including: - keep service area clean and dry - be sure electrical outlets and tools are properly grounded - use adequate light for the job Use only tools, jacks, and hoists of sufficient capacity for the job. Use heavy leather gloves to handle sharp objects. Land Rake 4 STORAGE SAFETY Store the unit in an area away from human activity. Do not permit children to play on or around the stored machine. Support the frame on stands and blocks to provide a secure base. SAFETY SIGNS The following illustration shows the approximate location and detail of safety signs. Keep all safety signs clean and legible and replace any that are damaged or missing. When original parts are replaced, any safety signs affixed to those parts should be replaced as well. Replacement safety signs are available from your local dealer. INSTALLATION To install safety signs, ensure the installation area is clean and dry. Decide on the exact position before you remove the backing paper. Remove the smallest portion of the split backing paper and align over the specified area. Carefully press in place. Slowly peel back the remaining paper and smooth the remaining portion in place. Small air pockets can be pierced with a pin and smoothed out. ASSEMBLY 1. Assemble the hitch (#1) and hitch brace (#2) on the t-frame using hardware supplied as shown in drawing. 2. The land rake frame is mounted on the t-frame with a 1” x 5” bolt (#17) on which the frame turns. The turntable pin (#8) locks the rake in place at the desired angle. Land Rake 5 START-UP 1. Park on a dry level area clear of debris. 2. Stop engine and set brake after lowering the three point arms so they line up with the mounting pins on the blade. 3. Mount the lower lift pins first and then adjust the rake angle using the turnbuckle on the top link. Check that all the clips holding on the three point pins are securely in place. 4. The land rake is designed to be used on tractors with up to 35 horsepower with a category 1 3-point hitch. OPERATION THEORY OF OPERATION Land Rake 6 OPERATION 1. Clear the area of bystanders and foreign objects before starting. 2. Use the float position on the three-point control to follow the contour of the ground. The weight of the blade will keep it down. 3. Maintain a speed that allows you to maintain control of your machine. 4. The 1” wide spring steel tines (#11) clear off unwanted material and prepare an ideal seedbed ready to accept small seeds or sod. It is also ideal for spreading and leveling crushed stone and other landscaping materials and can be used to maintain beaches and recreational areas 5 The rakes are adjustable to seven angles. ADJUSTMENT To change the angle of the rake, proceed in the following way: 1. Raise the rake off the ground. 2. Remove hair pin clip (#19) and the turntable pin (#8). 3. Grab one end of the rake and move it to the desired angle. 4. Install turntable pin and hair pin clip. MAINTENANCE Land Rake 7 MAINTENANCE Land Rake 8 WHEN ORDERING PARTS Always give your dealer the Model, Color and Serial Number of your machine to assist him in ordering and obtaining the correct parts. Use the exploded view and tabular listing of the area of interest to exactly identify the required part. LAND RAKE PARTS LIST ITEM PART # DESCRIPTION 1 F0351 Hitch Weldment 2 906768 Hitch Brace 3 906770 Spacer 1" O.D. x 2 1/4" Long 4 965807 Top Link Pin Category 1 5 965911 7/16" Linch Pin 6 965809 Lift Arm Pin with Nut & Washer Category 1 7 906767 T-Frame Weldment 8 967535 Turntable Pin 9 967564 60" Frame 967565 72" Frame 967566 84" Frame 967567 96" Frame 10 967568 60" Cross Bar 967569 72" Cross Bar 967570 84" Cross Bar 967571 96" Cross Bar 11 967572 Tines 5/16" x 1" x 15" 12 811795 3/8" x 2" Hex Bolt (pl) 4/Gauge Wheel 13 812363 3/8" Lock Nut (pl) 14 81722 7/8'' Hex Nut (pl) 15 811751 3/4" x 5" Hex Bolt (pl) 16 812365 3/4" Lock Nut (pl) 17 967527 1" x 5" Hex Bolt (pl) 18 967148 1" Lock Nut (pl) 19 12779 #9 Hair Pin Clip 20 84050 3/4" S.A.E. Flat Washer (pl) 21 967582 Arm Weldment 22 967583 Gauge Wheel Weldment 23 967138 12" x 1" Bore Solid Rubber Tire 24 967584 1" x 7" Yoke Pin (Cut Off Head) 25 9812434 1/4" x 1 1/2" Cotter Pin (pl) 26 966730 1" x 1 5/16" O.D. Bushing (pl) 27 966731 1/2" x 1 5/16" O.D. Bushing (pl) 28 967164 Pound-in Grease Nipple Land Rake 9 29 902277 Stand 30 901435 1/2" x 2 1/2" Clevis Pin (pl) 31 81626 1/2" x 2 3/4" Hex Bolt NC (pl) 32 961012 Hair Pin Clip #16 33 812364 1/2" Lock Nut (pl) 34 966729 3/16" Linch Pin (pl) 35 81593 3/8" Lock Washer (pl) 36 81592 3/8" Hex Nut (pl) 37 81578 3/8" x 1 3/4" Hex Bolt (pl) 38 966527 7/8'' x 2 1/2'' Hex Bolt (pl) 39 81723 7/8'' Lock Washer (pl) Land Rake 10 SHIPPING KIT AND BUNDLE NUMBERS The following is a list of Kit Num...