Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
To drain the oil, the machine must be tilted so that the oil runs out from the same hole. 4.9 Auxiliary wheel (1:H) The auxiliary wheel is intended to assist transportof the machine and has two positions. • The auxiliary wheel must not be installed when carrying out work. • The auxiliary wheel must be installed when transporting. Remove/install the auxiliary wheel as follows: 1. Pull out the locking pin (2:A). 2. Remove the auxiliary wheel downwards. 3. Reinstall the locking pin in the auxiliary wheel arm. Install in reverse order 4.10Rotors (1:J) Nobody must be close to the dangerous rotors during operation. The rotors are made of special steel and work the soil at the same time as the machine is propelled forwards. ENGLISH GB ENGLISH GB 4.11Cutting disc (1:K) Nobody must be close to the dangerous cutting discs during operation. The cutting discs are on respective rotor axles and are designed to border the working area and facilitate control of the machine. 4.12 Choke The choke must never be activated during operation. This will damage the engine. See the accompanying engine manual. The choke must be activated at cold starts. 4.13 Starting handle See the accompanying engine manual. Handle for starting the engine. 4.14Depth skid (1:G) The task of the depth skid is to keep the machine stable so that the soil can be cultivated. The depth skid has three positions. Shifting takes place as follows: 1. Pull out the locking pin (3:B). 2. Pull out the depth skid and reinstall in the desired position. 3. Reinstall the locking pin. The different operating properties are shown according to the table below: Holes Properties Left The machine works itself forward , angled to the left. Middle The machine works itself forward without being angled to either side. Right The machine works itself forward, angled to the right. 5 OPERATION 5.1 Fuel Read and understand all safety instructions. No fires or smoking near to petrol. Use 92-95 octane lead free petrol. Oil-mixed petrol designed for 2-stroke engines must never be used. Filling Read and understand all safety instructions. If the engine has been running, wait a few minutes until it has cooled before filling up. Fill carefully to prevent the spillage of fuel. Move the rotary cultivator at least 3 metres from the filling site before starting. Fill as follows: 1. Clean around the fuel cap. 2. Unscrew the filler cap. 3. Fill using a funnel or use a filler can with spout to prevent spillage. 4. Tighten the filler cap. 5. Move the rotary cultivator at least 3 metres from the place of filling before starting. Move the rotary cultivator at least 3 metres from the filling site before starting. 5.2 Engine Oil Always check the oil level before starting. Otherwise there is a risk of serious engine damage. Also see “4.8”. Check the oil level as follows: 1. Position the machine so that the engine is horizontal. 2. Unscrew the oil filler and check that the oil level is at the upper mark on the dipstick. See the accompanying engine manual. 3. Top up the oil if necessary. Use normal engine oil SAE 10W-30. 4. Reassemble the oil filler cap. Move the rotary cultivator at least 3 metres from the filling site before starting. ENGLISH GB ENGLISH GB 5.2.1 Starting the engine from cold 1. Put the choke in position “CHOKE”. See the accompanying engine manual. 2. Set the throttle (1:A) in the “START” position. 3. Hold the handle with one hand and slowly pull the starter handle with the other hand. See the accompanying engine manual. When the starter mechanism engages, quickly and forcefully pull the starter handle until the engine starts. NOTE! Do not pull the cord hard to its stop position and do not release it in the pulled out position. This damages the starter mechanism. 5. Reset the choke after 3-5 seconds. 5.2.2 Starting a warm engine Start a hot engine according to points 2 and 3 above. The choke/primer must not be used. 5.3 Operating 1. Tip the rotary cultivator back slightly so that the rotor is above ground. 2. Activate the drive control (1:D). 3. Tilt the cultivator forward so that it works its way into the soil. 4. If the machine has a reverse control, activate it (1:C). 5.4 Stop Stop the rotary cultivator by setting the throttle and stop control (1:A) to “STOP”. 5.5 Operating tips The rotors propel the machine forward. The speed of the rotors is controlled by the throttle (1:A). Keep hands and feet away from rotating parts (1:J, K). The optimum working depth varies with soil conditions. The working depth is determined by how hard the depth skid is pushed down during propulsion. Operate and test. Drive 2-3 times in different directions for best re sults. Never operate the machine in wet soil. Clumps of earth are created that are then difficult to break-up. Hard and dry soil requires an extra run, at right angles to the first. WARNING! Never overload a new machine. Drive carefully for the first 5 hours. 6 STORAGE Store the rotary cultivator in a dry place. Also see section “Safety instru...
Otros modelos de este manual:Cultivadores - SILEX 500-G (412.74 kb)