Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Lay all the loose parts in carton out on floor or work bench. , Separate all of the hardware (nuts and bolts) into groups. Preassemble eleven clamps {Ref. 10) and hex bolts 1/2" x 1.50" long (Ref. 4). Thread bolts into clamps until one thread shows through weld nut. Preassemble two wheels (Ref. 11), wheel rods (Ref. 14), shoulder bolts (Ref. 12) and hex lock \ nuts (Ref, 13). Place shoulder bolt through wheel and thread into wheel rod. Secure shoulder bolt with hex lock nut. Model No. 193-984A-000 PARTS LIST FOR CULTIVATOR MODEL NO. 193-984A-000 REF. NO. PART NO. QUANT. DESCRIPTION 1 43054 2 Hex Bolt 3/8-16 x 2.50" Lg, (Grade 5) 2 62342 1 Assembly Hitch Bar 3 43082 2 Hex L.-Nut 3/8-16-Thd.* 4 43020 11 Hex Bolt 1/2-13 x 1.50" Lg. (Grade 5) 5 43058 7 Plow Bolt 6 43016 7 Cultivator Point 7 43015 7 Hex Nut 3/8-16 Thd.* 8 43003 7 L.-Wash. 3/8" I.D.* 9 23040 7 Rod Shank 10 62026 11 Assembly Clamp 11 43021 2 Wheel 12 43029 2 Shoulder Bolt .489" Dia. x 1.450 13 43082 2 Hex L.-Nut 3/8-16 Thd.* 14 23042 2 Rod Gauge Wheel 15 43262 2 Hex L.-Nut 1/2-13 Thd.* 16 23325 1 Plate - Tie Bar 17 43634 2 Hex Bolt 1/2-13x3.00" Lg. (Grade 5) 18 62344 2 Assembly Adjustment Bar 19 62343 2 Assembly Side Bar 5. Preassemble seven shank rods (Ref. 9) and cultivator points (Ref. 6). Secure points to shanks with plow bolts (Ref. 5), lock washers (Ref. 8) and hex nuts (Ref. 7). 6. Place the tubes on the two side bars (Ref. 19) in between the welded brackets on hitch bar assembly (Ref. 2). 7. Pjacehex bolts 3/8 x 2-1/2" long (Ref. 1) through hitch bar and tubes on the end of the side bars. Start hex nuts (Ref. 3) by hand (Do Not Tighten). 8. Place one clamp (Ref. 10) on each side bar (open part of clamp faces the center of cultivator). 9. Pjace two adjustment bars (Ref. 18) with the weld pin end down through clamps. Overlap the other ends on hitch bar so that the two end holes line up with each other. RINTED IN U.S.A. Form No. 43633 1/83 10. Secure the ends of adjustment bars by placing two 1/2 x 3" long bolts (Ref. 17) down through adjustment bars (one bolt on each side of hitch bar),tie bar (Ref. 16) and hex lock nuts (Ref. 15V. 11. Tighten bolts and nuts at the front of hitch bar -and bolts on clamps. 12. Place one clamp (Ref. 10) on center of hitch bar. -Place one preassembled shank rod up through clamp and tighten hex bolt on clamp. 13. Place two clamps on ends of side bars. Next, place preassembled wheel rods up through clamps. Tighten hex bolts on clamps. ,: 14. Assemble the remaining six preassembled shank rods and clamps. OPERATING INSTRUCTIONS Cultivator may be used to straddle the row or work between rows. The hex bolts at clamps and bolts at adjustment. bars allow widening or narrowing of cultivator frame for different row widths. By sliding the clamps forward on side bars and moving the adjustment bars so they overlap (five holes), you can narrow the cultivator frame. The cultivator points and shanks may be moved up or down, forward or back by loosening the hex bolts on clamps, repositioning as desired and tightening hex bolt. The gauge wheels may be adjusted up or down in the same manner. FIGURE 1 To improve cultivator penetration and stability, it is suggested you add a weight to top of cultivator frame. See figure 1. A common concrete block maybe used or you may purchase weight, Part No. 723-0359. MTD PRODUCTS • P.O. BOX 36900 • CLEVELAND, OHIO 44136...