Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
The optional attachments are: MODEL: Edger ...................... PPB1000E Blower ..................... PPB3000B Brushcutter ................ PPB4000C WARNING: Always disconnect powerhead spark plug (or disconnect powerhead from powersource) beforeremoving or installing attachments. REMOVING ATTACHMENT CAUTION: When removing or installing attachments, place the powerhead and attachment on a flat surface for stability. 1. Loosen the coupler by turning the knob counterclockwise. CouplerUpper Shaft LOOSEN Lower Attachment TIGHTEN Knob 2. Press and hold the locking/release button. Locking/ReleaseButtonCouplerUpperShaftLowerAttachment 3. While securely holding the upper shaft, pull the attachment straight out of the coupler. INSTALLING ATTACHMENT 1. Remove the shaft cap from the attachment (if present) and discard. 2. Position locking/release button of attachment into guide recess of upper shaft coupler. Coupler Primary Hole GuideRecess Upper Shaft Locking/ Release Attachment Button 3. Push the attachment into the coupler until the locking/release button snaps into the primary hole. 4. Before using the unit, tighten the knob securely by turning clockwise. INSTALLING ATTACHMENT HANGER An attachment hanger is provided for storage when attachment is not in use. To install hanger on attachment: 1. Remove the shaft cap from the attachment (if present) and discard. 2. Press and hold the locking/release button. 3. Push hanger onto the attachment until the locking/release button snaps into the hole. OPERATING POSITION Long Pants Heavy Shoes ALWAYS WEAR: Eye Protection WARNING: To avoid personal injury, never carry the cultivator while the unit is running. WARNING: The gearbox gets very hot after extended periods of use. To avoid burns, do not touch the gearbox until it has been allowed to cool. CULTIVATING 1. Move the cultivator to the work area prior to starting the engine/motor. 2. With the engine/motor running and the tines off the ground, press the throttle trigger to increase the engine speed. 3. Hold trigger handle and assist handle firmly. Slowly lower the cultivator until the tines make contact with the ground. 4.Asunitbeginscultivating,pullbackontheunitsothatthetinescanpenetratetheground. 5 5. Once the ground has been broken, continue at a moderatepace until you are familiar with the controls and the handling of the cultivator. 6. Pull the cultivator backwards to improve the depth of cultivation and reduce your effort. 7. To cultivate in confined areas or narrow rows, remove the left and right outer tines (see TINE REPLACEMENT). MAINTENANCE WARNING: Always stopunitanddisconnect spark plug wire (or disconnect powerheadfrom powersource) beforeperforming maintenance. CHECK FOR DAMAGED OR WORN PARTS Contact an authorized service center for replacement of damaged or worn parts. S Tine Cover - --Discontinue use of cultivator if tine cover is damaged. CHECK FOR LOOSE FASTENERS AND PARTS S Clevis pins S Hitch pin clips INSPECT AND CLEAN UNIT AND DECALS S After each use, inspect complete unit for loose or damaged parts. Clean the unit and decals using a damp cloth with a mild detergent. S Wipe off unit with a clean dry cloth. TINE MAINTENANCE WARNING: The tines will continue to spin after the engine stops or after the throttle trigger has been released. To avoid serious injury, make sure the tines have stopped coasting and disconnect the spark plug (or disconnect powerhead from power source) before performing work on the tines. WARNING: Always replace tines that are bent, warped, cracked, broken, or damaged in any other way. Never attempt to straighten and reuse a damaged tine. Use only specified replacement tines. Wear protective gloves when handling or performing maintenance on the tines to help avoid injury. SERVICE AND ADJUSTMENTS TINE REPLACEMENT WARNING: The tines will continue to spin after the engine stops or after the throttle trigger has been released. To avoid serious injury, make sure the tines have stopped coasting and disconnect the spark plug (or disconnect powerhead from power source) before performing work on the tines. WARNING: Wear protective gloves when handling or performing maintenance on the tines to avoid injury. The tines become very sharp from use. 1. Remove the hitch pin clips and clevis pins. 6 HitchPinClipClevisPin 2.Removethetinesandfeltcushionsfromtheshaft. 3.Cleanandoiltheshaft. 4.Replacethetinesandthefeltcushions. 5. Repeat previous steps on opposite side. 6. Reinstall clevis pins and hitch pin clips. NOTE: When installed correctly, the hubs on the tines will face each other. The letters “R” stamped on the tines will be on the right side of the cultivator and the letters “L” will be on the left side. STORAGE WARNING: Perform the following steps after each use: S Allow attachment and gearbox to cool before storing or transporting. S Position attachment so that any sharp object cannot accidentally cause injury. S Store the attachment in a dry, well ventilated area out of the reach of child...
Otros modelos de este manual:Cultivadores - PPB2000T (142.12 kb)