Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
Be sure the cord is positioned with a “drip loop” below the level of the outlet as shown above. This prevents water from running down the cord and into the outlet. Instead the water will drip to the floor at the “drip loop” on the cord. To fill the water reservoir: 1. DISCONNECT FROM THE POWER SOURCE. 2. Loosen the tool rest adjustment lock handles and move the tool rest away from the sharpening stone. 3. Fill the water reservoir. See Figure 2 Fill Here Figure 2. Tool rest moved away from sharpening wheel. 4. With dry hands and a dry plug, connect the wet sharpener into the power source. 5. Run the wet sharpener for one minute to properly wet the stone. 6. With dry hands and a dry plug, disconnect the saw from the power source. 7. Refill the water reservoir until full and return the tool rest to the desired location. NOTE—It is important to keep the wheel well lubricated while sharpening. Unplug and refill machine as needed to maintain an appropriate water level. -6- Model H6069 Wet Sharpener Tool Rest Equipped with an adjustable tool rest, the Model H6069 enables precise control over the sharpening operation. Figure 3 shows the height and angle adjustment lock handles for the tool rest. Figure 3. Adjustment lock handles. Height Adjustment Handle Angle Adjustment Handle Adjusting the tool rest: 1. Loosen the height adjustment lock handle and move the tool rest to the desired height. 2. Tighten the height adjustment lock handle. 3. Apply Steps 1 & 2 to the angle adjustment lock handle to fine tune your sharpening angle. Operating this sharpener can propel objects into the air, causing imme- diate eye damage. To protect your- self, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment. Sharpening The Model H6069 Wet Sharpener, if properly used, will help you maintain the quality and life of your tools by keeping them sharp. Typical items you may sharpen with the wet sharpener include knives, chisels, planer blades, lathe tools and any other items around your shop that need to maintain a sharp edge. We recommend practicing with a tool of low personal value to get the feel of sharpening with this machine. Using the wet sharpener: 1. Turn the sharpener ON with the wheel rotating towards you. 2. Set the tool rest at the desired angle. 3. Place the blade on the tool rest. Using light pressure, press the blade against the wheel and slowly move side to side. Figure 4 Figure 4. Correct positioning on tool rest. 4. If you are sharpening a double edged tool such as a knife, turn the blade around and sharpen the opposite side. NOTE—If the tool you are sharpening has a one-sided edge such as a chisel or planer blade, DO NOT follow this step. Model H6069 Wet Sharpener -7 MAINTENANCE Reservoir Rinsing With use, the water reservoir will begin to fill with ground material from the objects being sharpened and wheel particles removed during the sharpening process. Keep the water reservoir clean and free of residue build up. To rinse the water reservoir: 1. UNPLUG THE SHARPENER FROM THE POWER SOURCE. 2. Tilt the sharpener to drain any water in the reservoir through the drain trough on the back of the sharpener. 3. Move the tool rest away from the grinding wheel. 4. Fill the reservoir with fresh water and empty from the drain trough. Repeat until clean. Reduce the risk of electrocution by keeping all connections dry and off the ground. DO NOT touch plugs with wet hands. Failure to follow these warning could result in serious injury. -8- Model H6069 Wet Sharpener NOTES Model H6069 Wet Sharpener -9 12337484948567154714131211109161719184241251720394035363445431221223823122426283227312930334424H6069 Wet Sharpener Parts Breakdown DESCRIPTIONREF PART # H6069 Wet Sharpener Parts Breakdown DESCRIPTIONREF PART # 1 PH6069001 UPPER HOUSING 2 PCB14 CARRIAGE BOLT #10-32 X 3/8" 3 PH6069003 LEFT SUPPORT 4 PH6069004 RIGHT SUPPORT 5 PH6069005 PLASTIC WASHER 3/16" 6 PH6069006 LOCK HANDLE NUT 3/16-32 7 PH6069007 LOCK HANDLE LEVER 8 PRP61M ROLL PIN 3 X 12 9 PH6069009 POWER BELT 3/8" X 10" 10 PR16 EXT RETAINING RING 11 PH6069011 WHEEL GEAR -10-Model H6069 Wet Sharpener Model H6069 REF PART # DESCRIPTION 12 PHTEK29 TAP SCREW #5 X 1/2" 13 PH6069013 BEARING HOLDER 14 PH6069014 PLAIN BEARING 22MM X 11MM 15 PH6069015 WHEEL SHAFT ASSEMBLY 16 PS86M PHLP HD SCR M6-1 X 55 17 PW03M FLAT WASHER 6MM 18 PH6069018 AXLE SLEEVE 19 PH6069019 REDUCTION GEAR 20 PLN03M LOCK NUT M6-1 21 PH6069021 CAPACITOR HOLDER 22 PC006 CAPACITOR 6MFD 250V 23 PH6069023 POWER SWITCH 24 PHTEK6M TAP SCREW M4 X 16 25 PH6069025 LOWER HOUSING 26 PH6069026 CLAMPING PLATE 27 PH6069027 POWER CORD 28 PH6069028 STRAIN RELIEF 29 PH6069029 FAN 30 PS25M PHLP HD SCR M4-.7 X 35 31 PH6069031 RIGHT MOTOR HOUSING 32 P6200 BALL BEARING 6200 33 PH6069033 FOOT PADS 34 PH6069034 LEFT MOTOR HOUSING 35 PB97M HEX BOLT M4-.7 X 12 36 PW05M WASHER 4MM 37 PH6069037 TOOL REST 38 PH6069038 CAPACITOR SLEEVE 39 PS17M PHLP HD SCR M4-.7 X 6 40 PTLW11M...