Votos - 5, Puntuación media: 4.4
(
)
)
|
Resumen del manual
2. Dry with a soft cloth. Wipe the motor/heating element housing with a soft clean cloth or sponge. 3. Allow unit to dry completely before assembly or use. 4. After washing and drying, apply a small amount of salad oil (not included) to Cutting Plates to keep them lubricated. CAUTION: Do not clean with bleach, thinners or benzine. These will damage or discolor Meat Grinder. Assembly Read the ENTIRE IMPORTANT SAFEGUARDS section at the beginning of this manual including all text under subheadings therein before set up or use of this product. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION OR ELECTRIC SHOCK: Turn the appliance off, unplug the cord, and allow the appliance to cool completely before performing any procedure in this section. Do not immerse the motor/heating element, cord, or plug. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. 1. Slide Head (12) into Housing Opening (15). While holding Head, place Locking Knob (22) into slot on Left Motor Housing (21). 2. Turn Locking Knob clockwise until tight and Head is fastened securely to housing. 3. Twist Feed Screw (100) long-end first into Head. Continue twisting until Feed Screw fastened into housing. 4. Slide Cutting Blade (9) onto Feed Screw, making sure the edges of Cutting Blade face front of housing. CAUTION! Cutting Blade is sharp. Wear gloves and use care when installing Cutting Blade. 5. Slide selected Cutting Plate (6, 7, or 8) over Cutting Blade, using the slot along Plate edge as guide. 6. Screw Cap (1) into place on housing until secure. WARNING! To prevent metal filings in food and serious injury from grinder damage: Lubricate with salad oil before use. Do not overtighten Cap (1). Stop and check Cap (1) periodically during use to ensure it remains tight. 7. Slide Hopper Plate (13) onto top of Head until secure. 8. Set Grinder on flat and stable counter space that does not block vents along bottom of housing. 9. Cut foods into small pieces that can easily fit into Hopper. REV 12c Operating Instructions Read the ENTIRE IMPORTANT SAFEGUARDS section at the beginning of this manual including all text under subheadings therein before set up or use of this product. 1. Once food is ready, plug in Power Cord (17) and press Switch (20) to activate. 2. Feed food into Hopper Plate. Use Food Pusher (14) to press food down Plate and into Head. WARNING! Do NOT use fingers to push food into Grinder. Only use Food Pusher. 3. To make sausage, insert desired Sausage Maker (3, 4, or 5) into Sausage Adapter (2). 4. Place wide end of Sausage Adapter against the Head and in front of Cutting Blade. 5. Slide Cap over Sausage Maker and Adapter and turn clockwise until Sausage Adapter is fastened securely against housing. CAUTION! Do not overtighten. 6. For making Kubbe, place Kubbe Attachments (10, 11) onto Feed Screw shaft. Slide down until the Attachment tabs fit into the slots. 7. Slide Cap over Attachments and turn clockwise until fastened securely against housing. WARNING! To prevent metal filings in food and serious injury from grinder damage: Lubricate with salad oil before use. Do not overtighten Cap (1). Stop and check Cap (1) periodically during use to ensure it remains tight. 8. To prevent accidents, turn off the appliance and disconnect its power supply after use. Clean, then store the appliance indoors out of children’s reach. Inspection and Maintenance Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION OR ELECTRIC SHOCK: Turn the appliance off, unplug the cord, and allow the appliance to cool completely before performing any procedure in this section. Do not immerse the motor/heating element, cord, or plug. TO PREVENT SERIOUS INJURY FROM APPLIANCE FAILURE: Do not use damaged appliances. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication 1. BEFORE EACH USE, inspect the general condition of the appliance. Check for: • loose hardware, • misalignment or binding of moving parts, • cracked or broken parts, • damaged electrical wiring, and • any other condition that may affect its safe operation. 2. TO CLEAR JAMS: a. Switch off Grinder and unplug it. b. Unscrew Cap and use a screwdriver to remove Cutting Plate. CAUTION! Do not remove Cutting Plate with fingers. c. Remove clog. d. Wash washable parts in warm, soapy water. e. Dry parts and reassemble them. 3. WARNING! If the supply cord of this appliance is damaged, it must be replaced only by a qualified service technician. REV 12c Parts List and Diagram Part Description Qty 1 Cap 1 2 Sausage Maker Adapter 1 3 Small Sausage Maker 1 4 Medium Sausage Maker 1 5 Large Sausage Maker 1 6 Medium Cutting Plate 1 7 Fine Cutting Plate 1 8 Coarse Cutting Plate 1 9 Cutting Blade 1 10 Kubbe Attachment A 1 11 Kubbe Attachment B 1 12 Head 1 13 Hopper Pl...
Otros modelos de este manual:Utensilios de cocina - 99598 (361.69 kb)