Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
DISPLAY 2 • Once the ProClick® Pronto™ ™™™™™ has measured the document thickness, the display will indicate the correct spine size to load into the machine. The example shown in Display 2 indicates “Small” under “Insert correct ProClick® spine size”. • The system will allow you to bind small documents with larger spine sizes. • Insert the appropriate spine cassette into spine slot as shown in Display 2. DISPLAY 3 DISPLAY 4 • Press “BIND” to bind your document and remove the document after you hear a BEEP. • Additional documents can be bound without resizing, if binding books are of the same document size. • The ProClick® Pronto™ ™™™™™ will time out to the first step if it stays idle for 2 minutes. You will need to resize your document to continue. 4.6 Editing your document The ProClick® Pronto™ ™™™™™ has a special spine opener tool where you can unbind the bound book for editing. To unbind a bound book, just insert the wedge of the spine opener tool into the loops of the ProClick® spine and pull forward in a sliding action. This opens the ProClick® allowing you to edit the documents and manually resecure the bind spine. (Text Box comment (Text Box comment 800.543.5454) (Text Box comment Office Zone) ProClick Pronto® ™™™™™ 5.0 Troubleshooting ENG ProClick Pronto® ™™™™™ 5.0 Troubleshooting ENG Problem Solution No Power, No Lights .. Verify unit is plugged in. .. Check ON/OFF Switch. No Power, No Lights, Unit Is Plugged In, ON/OFF Switch is ON. ..• Contact an Authorized GBC Technician for Service. Empty Chip Tray When the chip tray is full (approximately 60 books) the User Interface will show the Icon below indicating the tray is full and needs to be emptied. • Pull Tray out and empty tray • Replace empty tray The machine will NOT operate without the chip tray securely in place Removing a Jam Open Cover Slide Tray Up • Remove jammed Spine. • Lower paper desk back into the original operating position. • Push Clear Safety Cover back into position. • The ProClick® Pronto™ ™™™™™ is now clear and ready to proceed. • Remove jammed document. • Lift paper deck from the center into the locked/resting position by pulling the tray upwards from the middle. (Machine is now disabled and cannot operate until the paper desk and safety cover have been put back into their proper original operating position). • • • Pull Clear Safety Cover forward (Machine is now disabled and cannot operate until the safety cover have been put back into their proper original operating positions). • Remove single spine, Slide Tray down and close cover “Remove Document” means: “Open Cover” means: “Slide Tray Up” means: “Remove single spine, Slide Tray down and close cover” means: Remove Document • Flashing Error Display • If error display flashes on the User Interface, reboot the machine by turning the machine off and turning it on. • If the machine still shows the same error flashing, call a service technician for assistance. Not ready to bind • The machine will detect all inputs (binding spine not in machine, document size not measured, safety cover closed) before allowing binding to proceed. • If any of these are not in place, the machine will not bind and the user interface will display the corresponding requirement for user action. Machine does not resize • Make sure that there is no paper on the paper deck when inserting spine. • If the bind spine is smaller than the sized document, the machine will not bind. • If user interface display “Insert punched document into sizer”, the user will need to resize the document in the document sizer. Power Cord has been lost Contact an Authorized GBC Technician to order replacement parts. Please provide the machine model and serial number for reference. Wrong sequence of operation If user inserts the document before inserting the spine cassette, the user interface will show a “Remove document” error. Remove the document and follow the instruction on the user interface. (Text Box comment (Text Box comment 800.543.5454) (Text Box comment Office Zone) ProClick Pronto® ™™™™™ LIMITED 1 YEAR WARRANTY ProClick Pronto® ™™™™™ LIMITED 1 YEAR WARRANTY General Binding Corporation (“GBC”) warrants to the original purchaser for a period of one (1) year after purchase that this GBC product is free from defects in workmanship and material under normal use and service. GBC’s obligation under this warranty is limited to replacement or repair, at GBC’s option, of any warranted part found defective by GBC without charge for material or labor. Any replacement, at GBC’s option, may be the same product or a substantially similar product. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. REPRESENTATIONS OR PROMISES INCONSISTENT WITH, OR IN ADDITION TO, THIS WARRANTY ARE UNAUTHORIZED AND SHALL NOT BE BINDING UPON GBC. IN NO EVENT SHALL GBC BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER OR NOTFORESEEABLE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION ...
Otros modelos de este manual:Laminador - PRO CLICK PRONTO P2000 (919.82 kb)