Votos - 4, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Center the film and tighten the core screws (Figure 2). 3. Load a roll of mounting film or roll of craft paper to the bottom film shaft. Do not tighten the core screws at this time.(Figure 3) Note: Please see the direction of the film on the top and bottom shafts. 4. Load the top and bottom film shafts onto the machine (Figure 4 & 5). 10 ¿RS§s£™9„ 12. THREADING FILM only RSC-1650HR 12.1. Decaling 1. Turn the power switch on (“I” position). The Power switch is located on the rear left side of the unit. 2. Complete the steps as in the “LOADING FILM” section (see page 10). 3. Set the top roller to the desired temperature (RSC-1650H and RSC-1650HR) 4. Take off the Frame-Paper Guide and the Feed Table. 5. Pull the top film down over the Safety Cover to the bottom of the craft paper / Mounting film. 6. Align and center the craft paper / Mounting film to the top film and tighten the two lower core screws (Figure 1). 7. Thread the top film underneath the Upper Idle Bar.(Figure 2) 8. Tape the top film on to the Release Liner Take-Up.(Figure 2) Figure 2 Figure 1 11 RSC Series 9. Cut and separate the release liner and the film. (Figure 3) 10. Thread the craft paper behind the Lower Idle Bar to the top film that is resting on the main roller (do not use the Lower Idle Bar for Mounting). (Figure 4) 11. Reinstall the Feed Table and the Frame-Paper Guide,and close the Safety Cover. 12. Adjust the nip setting to appropriate gap. 13. Insert and push the leader board until they reach the front nip point. 14. Push the Run button. 15. Push the leader board into the rollers. (Figure 5) Figure 5 16. Adjust the top and bottom tension knob by rotating it clockwise or counterclockwise. Turn it until the top and bottom roll films have some resistance varies (the tension depending on the film thickness; the thicker the film the more tension is required). (F'gure 6) Figure 6 Figure 3 Figure 4 12 ¿RS§s£™9„ 17. Press the Stop button when the leader board has completely exited from the rollers. 18. Use the Cross Cutter to cut the leader board from the web (see page 9). 19. Set the nip setting to the appropriate position for the Over-lamination / Decaling application. 12.2. Mounting 1. Lay the decaled image face down on a flat surface. Carefully peel back and put a crease along the edge of the release liner ( Approximately 1 in or 25mm, Figure 1). 2. With the image facing up, align the image onto the board. Press firmly from the center out (Figure 2). 3. Adjust the pressure lever to ensure the proper opening (Figure 3). Figure 2 Figure 3 13 RSC Series 4. Flip the image over the top roller and hold on to the release liner (Figure 4). Figure 4 5. Press the foot pedal once, and then let it go while slowly pulling the release liner as the board enters the main roller nip (Figure 5) 6. Press the foot pedal once again when the board has completely exited from the rear of the unit. Trim the board if necessary. 14 ¿RSËArign 13. INSTALLATION OF FRONT FEEDER and REAR REWINDER OPTIONS Note: Below options are to be installed by an authorized RS reseller. Installation of the Front Feeder Option (Includes 2 brackets, one spindle, and mounting hardware). 1. Install the Front Feeder to the inside of the front frames using four 1/4"(M6) hexagon bolts on each side (Figure 1) Figure 1 Installing the Rear Rewinder Option (Includes motorized winder, bracket, one spindle, and mounting hardware). 1. Remove the left and right covers by using a Phillips screwdriver (four screws on each side cover) (Figure 2 & 3). 2. Remove the lever knob screw and lever (Figure 4). 3. Remove the rear cover by removing all 10 screws (4 top, 4 bottom, and 1 on each side) (Figure 5 & 6). Figure 5 Figure 6 Figure 2 Figure 3 15 RSC Series 4. Disassemble the power switch bracket and place the left rewinder outside of the frame; fasten with round head 3/16"(M5) screws (included in the option kit). Then, reinstall the power switch bracket (Figure 7). 5. Install the right rewinder on the outside of the frame and connect the motor wire connector to the rear wire (Figure 8 & 9). Figure 7 Figure 8 Figure 9 6. Reinstall the rear cover. 7. Reinstall the side covers. 8. Reinstall the lever knob and screw. 16 ¿RSË&rign 14. MAINTENANCE Cleaning the Body of the laminaor 1. To clean the machine body, dampen a cloth with water only and gently wipe the machine clean. Removing Adhesive Build Up 1. Remove the film from the laminator. 2. Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the Teflon (metal) and silicone rollers. Note: Rub firmly but do not scrub the rollers vigorously as this may scratch the surface.Do not use sharp metal objects, steel wool, or abrasives, as these may also damage the rollers. Lubrication 1. Drive chain and sprockets should be lubricated with either a light coat of gear lube or heavy grease (lithium grease) after 6 months or 1000 hours of operation, whichever co...
Otros modelos de este manual:Laminador - RSC-1650 (4.41 mb)
Laminador - RSC-1650HR (4.41 mb)