Votos - 4, Puntuación media: 4.8
(
)
)
|
Resumen del manual
PAGE 7 FIGURE H (REAR VIEW) FIGURE H (REAR VIEW) 1. With additional help, set the Bandsaw Body on the Stand. Make sure the Table (36B) faces to the frontof the Stand. 2. Align the four mounting holes on the Base (2B) of the Bandsaw Body with the holes located on the Face Plate (1A) of the Stand. 3. Attach the Bandsaw Body securely to the Stand, using the four Hex Bolts, Washers, Spring Washers, and Nuts (III). (See Figures I, J, and Hardware Diagram.) FIGURE I FIGURE J REAR VIEW To MountThe V-Belt Onto The Belt Pulley And Motor Pulley - Model 32206/ Single Speed: 1. Open the Side Panel Door (38A). (See Figure K.) SKU 32208/32206 For technical questions, please call 1-800-444-3353. PAGE 8 2. Place the V-Belt (2C) onto the Belt Pulley (23B) and also onto the Motor Pulley (1C). NOTE: During this step, you may need to push the Motor (11A) upward along the grooves in the Motor Plate (10A) in order to mount the V-Belt onto the Motor Pulley. (See Figures G and H.) 3. To adjust the V-Belt (2C) to its proper tension, pull down on the Motor (11A). While pulling down on the Motor, push in on the V-Belt with your finger until the V-Belt can only be pushed in about 1/2”. While holding the Motor in place, wrench tighten the Motor (11A) to the Motor Plate (10A) with the four Hex Bolts, Washers, Spring Washers, and Nuts (IV). (See Figures G and H.) 4. NOTE: For additional technical information, see Figure M. 5. While the Side Panel Door (38A) is still open, attach the Knob (VI) to the Door. Then, close the Side Panel Door securely. (See Figure K and Hardware Diagram.) To MountTheV-Belt OntoThe Belt Pulley And Motor Pulley - Model 32208/ Four Speed: 1. Open the Side Panel Door (38A). (See Figure K.) 2. NOTE: This particular model Bandsaw features four different RPM speeds from which to choose. In order to mount the two V-Belts onto the correct pulleys to achieve the desired RPM see Figure M. 3. Place the V-Belt (5D) onto the Belt Pulley (23B) and also onto the Middle Pulley (1D). (See Figure L.) 4. Place the other V-Belt (4D) onto the Middle Pulley (1D) and also onto the Motor Pulley (3D). NOTE: During this step, you may need to push the Motor (11A) upward along the grooves in the Motor Plate (10A) in order to mount the V-Belt onto the Motor Pulley. (See Figures G and H.) 5. To adjust the V-Belt (4D) to its proper tension, pull down on the Motor (11A). While pulling down on the Motor, push in on the V-Belt with your finger until the V-Belt can only be pushed in about 1/2”. While holding the Motor in place, wrench tighten the Motor (11A) to the Motor Plate (10A) with the four Hex Bolts, Washers, Spring Washers, and Nuts (IV). (See Figures G and H.) REV 07/01 SKU 32208/32206 For technical questions, please call 1-800-444-3353. PAGE 9 FIGURE K 6. While the Side Panel Door (38A) is still open, attach the Knob (VI) to the Door. Then, close the Side Panel Door securely. (See Figure K and Hardware Diagram.) FIGURE M FIGURE L 3000 600 1140 1670 2670 SKU 32208/32206 For technical questions, please call 1-800-444-3353. PAGE 10 To InstallThe Side PanelsToThe Stand: To InstallThe Side PanelsToThe Stand: With a Philips screwdriver, start the Tapping Screws (40A) into the Relief Stops (39A). (See Figure N.) 2. Attach the Relief Stops (39A) to the Side Panel (38A) by partially screwing the Tapping Screws (40A) into the mounting holes on the Side Panel. The Stops are highlighted in Figure O - step 1. 3. Position the Relief Stops (39A) so that the Stops (39A) point towards the center of the Side Panel (38). 4. While holding the Side Panel (38A) by the two finger holes, place it inside the side of the Stand as shown in Figure O - step 2. Rotate the Relief Stops (39A) out and screw in the Tapping Screws (40A) to secure the Side Panel in place. Repeat the process for the other Side Panel (38A). To InstallThe Saw Blade: Wear Gloves; be careful of sharp blade teeth when handling. 1. Remove the four Knobs (15B) from the Upper and Lower Wheel Guards (14B, 21B). (See Figure P.) 2. Remove and set aside the Upper and Lower Wheel Guards (14B, 21B). 3. Remove the Table Insert (37B) and Table Pin (38B). (See Figure Q.) FIGURE N FIGURE P FIGURE Q 38B 37B REV 07/04 FIGURE O Step 1 Step 2 SKU 32208/32206 For technical questions, please call 1-800-444-3353. PAGE 11 4. Turn the Blade Adjusting Screw (5B) counterclockwise about 5-10 full turns. (See Figure R.) 5. With both hands, hold the Saw Blade with its teeth pointing downwardand away from your body. Then, insert the Saw Blade through the horizontal slot in the Table (36B). (See Figure S.) 6. Place the Saw Blade on the Upper and Lower Wheels (16B, 19B). (See Figures T and U.) FIGURE R FIGURE S 7. Position the Saw Blade in the Upper and Lower Blade Guides (29B, 32B). (See Figures T and V.) 8. Replace the Table Insert (37B) and Table Pin (38B). (See Figure Q.) 9. Replace the Upper and Lower Wheel Guards (14B, 21B), and secure the Guards to the Bandsaw with the four Knobs (15B). (See Figure P.) FIGURE T FIGU...
Otros modelos de este manual:Jig Saw y - 32208 (2.05 mb)