Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
Unsharpened or improperly set wheels produce narrow kerf causing excessive friction, wheel binding and KICKBACK. Wheel depth and bevel adjusting locking levers must be tight and secure before making cut. If wheel adjustment shifts while cutting, it will cause binding and KICKBACK. Use extra caution when making a “Pocket Cut” into existing walls or other blind areas. The protruding wheel may cut objects that can cause KICKBACK. 11. Use only diamond wheels. NEVER use tool with wood cutting blades or other sawblades. Such blades when used on this tool frequently kick and cause loss of control leading to personal injury. 12. Check the wheel carefully for cracks or damage before operation. Replace cracked or damaged wheel immediately. 13. Use only flanges specified for this tool. 14. Be careful not to damage the spindle, flanges (especially the installing surface) or bolt. Damage to these parts could result in wheel breakage. 15. Hold the tool firmly. 16. Make sure the wheel is not contacting the workpiece before the switch is turned on. 17. Wait until the wheel attains full speed before cutting. 18. Stop operation immediately if you notice anything abnormal. 19. Never attempt to cut with the tool held upside down in a vise. This can lead to serious accidents, because it is extremely dangerous. 20. Do not stop the wheel by lateral pressure on the disc. 21. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data. SAVE THESE INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD301-1 The followings show the symbols used for tool. V .......................volts n....................no load speed ° ................... direct current .../min................revolutions or reciprocation per minute IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CARTRIDGE 1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 2. Do not disassemble battery cartridge. 3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. 4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. 5. Always cover the battery terminals with the battery cover when the battery cartridge is not used. ENC004-1 6. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. 7. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F). 8. Do not incinerate the battery cartridge pletely worn out. The battery cartridge can even if it is severely damaged or is comexplode in a fire. 9. Be careful not to drop or strike battery. SAVE THESE INSTRUCTIONS Tips for maintaining maximum battery life 1. Charge the battery cartridge before com-3. Charge the battery cartridge with room pletely discharged. temperature at 10°C - 40°C (50°F - 104°F). Always stop tool operation and charge the Let a hot battery cartridge cool down battery cartridge when you notice less before charging it. tool power. 4. Charge the Nickel Metal Hydride battery 2. Never recharge a fully charged battery cartridge when you do not use it for more cartridge. than six months. Overcharging shortens the battery service life. FUNCTIONAL DESCRIPTION FUNCTIONAL DESCRIPTION 1 2 1. Battery cartridge 2. Button 003512 1 3 2 1. Depth guide 2. Clamping screw 3. Base 003513 1 2 3 1. Depth guide 2. Top of notch 3. Graduation CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Installing or removing battery cartridge • Always switch off the tool before insertion or removal of the battery cartridge. • To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. • To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. • Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly. Adjusting the depth of cut Loosen the clamping screw on the depth guide and move the base up or down. You can read the depth of cut by aligning the top of the notch in...