Votos - 5, Puntuación media: 4 ( )

Fabricar: Dolmar Tamaño del archivo: 3.5 mb Nombre del archivo: Idioma del manual:

965 300 470 965 300 470 Overall weight (tanks empty, without cutting disc) lb 21.38 21.82 21.6 22.04 2) Circumference speed at max. engine speed3) Outside diameter / arbor hole / thickness 4) Country-specific 13 Denomination of components (Illustration shows model PC-7335) 1 Handle 2 Filter cover for air filter and spark plug cap 3 Cover lock 4 Tubular handle 5 Muffler 6 Protection hood 7 Grip 8 V-belt tension adjusting screw 9 Retaining nuts 10 Stand 11 Carburetor adjustment opening 12 Identification plate 13 Fuel tank with handle 14 Decompression valve 15 Starter grip 16 Air intake 17 Combination Start/Stop (I/O) switch, choke 18 Stop knob for halfway throttle 19 Safety locking button 20 Throttle lever 21 Tank cap (fuel) 22 Starter housing with starter 23 Cutting disc 24 Disc bolt 25 Spring washer 26 Hold opening 1 24 25 23 2 3 4 5 6 7 8 26 14 15 16 17 18 19 20 9 10 22 21 13 12 11 Serial number Year of manufacture Identification plate (12) PC-7335 Indicate when ordering spare parts 0410 123456 DOLMAR GmbH, 22045 Hamburg, Germany 394.100. 256 Typ 394 EMI OFB 973108 CAUTION: Always turn off the engine and pull off the spark plug cap before doing any work on the Power Cut! Always wear protective gloves! CAUTION: Start the Power Cut only after complete assembly and inspection. For the the following work, use the assembly tools included with delivery: 1. 13/19 AF combination wrench 2. Allen key 3. Carburetor adjustment screwdriver 4. Adapter ring (not in the general delivery inventory) Place the Power Cut on a stable surface and carry out the following assembly steps: Only for models PC-8135 and 8140 No air filter is installed! Before operation, insert an oiled foam filter (pre-filter), as shown in the adjacent illustration! To do this, take off the filter cover (see the chapter on Cleaning / changing the air filter). Sequence Mounting the cutting disc Inspect the disc for damage. See SAFETY INSTRUCTIONS, Page 7. Unscrew screw (9) and remove the spring washer (8). Place the cutting disc (5) on the arbour (7). Hinweis: The arbor hole of the cutting disc must be an exact fit with the arbor or shaft. If the arbor hole is larger, it must be fitted with an adapter ring (*). Make sure the cutting disc is installed so it turns in the right direction, if a direction is marked on the disc. Place the spring washer (8) on the arbour and insert the screw (9) and tighten by hand. Turn the disc slowly until the stop hole of the V-belt pulley is visible in the cutting arm cover (10). Insert the Allen key (2) as far as it will go. The shaft is now blocked. Tighten the screw with the combination wrench (1) NOTE: Tighten the screw firmly (30 ± 2 Nm), as otherwise the cutting wheel may slip during cutting. Tightening the V-belt / Checking V-belt tension IMPORTANT: Exact V-belt tension is essential for maximum cutting performance with minimum fuel consumption. Improper V-belt tension will result in premature wear to the V-belt and V-belt wheel or damage to the clutch bearing. If the Power Cut is new or the V-belt has been replaced, retighten the V-belt after the first hour of operation! Tightening the V-belt / Checking V-belt tension IMPORTANT: Exact V-belt tension is essential for maximum cutting performance with minimum fuel consumption. Improper V-belt tension will result in premature wear to the V-belt and V-belt wheel or damage to the clutch bearing. If the Power Cut is new or the V-belt has been replaced, retighten the V-belt after the first hour of operation! Installing the pressure water system Not in the general scope of delivery. Country-specific! 15 CAUTION: Before doing any work on the Power Cut, always switch off the engine and disconnect the spark plug cap! 16 NOTE: When using a protective hood for a maximum disk diameter of 300 mm (12"), always shorten hose (15) to 180 mm (7"). 21 To do this unscrew sleeve (16) and carefully pull tube (15) off coupling (17) and cut to 180 mm. Then push the tube end back over the coupling and tighten the sleeve all the way. 17 -Install the water connection as shown in figure. Push clamp (22) around the front grip (23) and fasten with the bolt and square nut. -Pull the quick-release coupling (24) from the water connection and connect it to the 1/2" supply line (18). -Remove the cutting disk (see instruction manual). -Tube routing with the cutting assembly in the middle position, see figure. -Tube routing with the cutting assembly in the outside position, see figure. -Insert the nozzles (19) through the protective hood (20) from the inside and put on couplings (17). Screw on and tighten the coupling caps (21). IMPORTANT: To avoid bending the tubes, be sure to position the couplings (17) in accordance with figures as appropriate. -Install the cutting disc (see instruction manual). -Connect the quick-release coupling (24) to the supply tube. NOTE: The water flow rate can be precisely adjusted with valve (25). 19 21 17 20 18 * Fuels Caution: The Power Cut uses mineral-oil products (gasol...

Descargar ahora

Introduzca dos números de la imagen: