Votos - 5, Puntuación media: 4.2
(
)
)
|
Resumen del manual
Dull blades may cause the saw to swerve or stall under pressure. IF YOU DROP or damage the saw, unplug it first; then check to see if the blade and lower blade guard operate freely before resuming operations. IF SAW STALLS, release the trigger and disconnect plug from power supply before attempting to loosen the unit. MOTOR Your Black and Decker tool is powered by a B&D-built motor. Be sure your power supply agrees with voltage marked on nameplate. Volts AC means Alternating Current (25 to 60 cycles) only. Volts AC/DC means it will also operate on Direct Current (single speed unit only). Voltage variation of more than 10% will cause loss of power and over-heating. All B&D tools are factory-tested. If this tool does not operate, check the power supply line for blown fuses and the plug and receptacle for proper contact. GROUNDING These units are equipped with approved 3-conductor power cord and 3-prong grounding type attachment plug to be used with the proper grounding type receptacle, in accordance with the National Electrical Code, Canadian Electrical Code, and Underwriters' Laboratories specifications. The green colored conductor in the cord is the grounding wire. It is connected to the metal frame of the unit inside the housing and to the longest prong of the attachment plug. Never connect the green wire to a "live" terminal. If your unit requires less than 150 volts it has a plug that looks like Fig. “A”. It will fit directly into the proper type of 3-wire grounding receptacle. The unit is then grounded automatically each time it is plugged in. Shown in Fig. “B” is a special grounding adapter (not allowed in Canada by the Canadian Electrical Code) which is available from your dealer and will permit using a 2-wire receptacle. The green grounding wire extending from the side of the adapter must be connected to a Permanent Ground. If the unit requires from 150 to 250 volts, it has a plug like Fig. "C". No adapter is available and the plug must be used in the proper 3-wire grounding receptacle. If you use an extension cord, be sure that it is a 3-conductor, grounding type cord. Grounding must be continuous from the tool plug to the grounded receptacle. GROUNDED OUTLET BOX-* / GROUNDING PRONG IS LONGEST OF THE 3 PRONGS © © GROUNDED OUTLET BOX**! GROUNDED OUTLET BOX.* GROUNDING PRONG IS LONGEST OF © THE 3 PRONGS C EXTENSION CORD When using the tool at a considerable distance from power source, a 3-conductor, grounding-type extension cord of adequate size must be used for safety, and to prevent loss of power and over-heating. Use the table below for 120-volt tools. For 220-voIt tools, see same chart but use a wire size corresponding to an extension cord length shown which is y2 the length of extension to be used. P.T.I. Safety Rule #12 applies to Extension Cords as well as the Tool Power Cord. Before using cords, inspect them for loose or exposed wires and damaged Insulation. Make any needed repairs or replacement before using your power tool. Ampere rating 0 to 2.10 to 3.5 to 5.10 to 7.10 to 12.1 to (on nameplate) 2.0 3.4 5.0 7.0 12.0 16.0 Ext. Cable length Wire Size (A.W.G.) 25 ft. 18 18 18 18 16 14 50 ft. 18 18 18 16 14 12 75 ft. 18 18 16 14 12 10 100 ft. 18 16 14 12 10 ___ 150 ft. 16 14 12 12 ___ __ 200 ft. 16 14 12 10 — — Form No. 97747.ni MOUNTING SAW BLADES BEVEL ANGLE ADJUSTMENT 1, BE SURE THE SAW IS DISCONNECTED FROM THE POWER SUPPLY! 2, To remove blade clamping screw: — a. ON NEW SAWS (without blade attached), turn screw counter-clockwise with blade wrench provided. If screw does not loosen easily from spindle, tap the outer end of the wrench sharply in a counter-clockwise direction with a piece of wood to “free'1 the screw threads, Remove screw and outer clamp washer, - b. ON SAWS WITH BLADE ATTACHED, turn the blade so that the single hole in the rim is exposed at the front of the saw. Put a nail through this hole and turn the blade counterclockwise until the nail is against the housing and stops the - blade from turning. Turn the blade clamping screw counterclockwise with the blade wrench and remove the-screw and outer clamp washer. 3, To attach the blade, retract the lower blade guard and slip the blade over the saw spindle against the inner clamp washer with printed side of blade out (teeth at bottom of blade pointing forward). Place outer clamp washer or spindle so that “flats” in washer fit “flats” on spindle. Thread on clamping screw to hold washer in position. Place a nail through hole in blade rim so that nail, rests on front of saw base and keeps blade from turning. Tighten clamping screw (clockwise) securely with the blade wrench. CUTTING DEPTH ADJUSTMENT BE SURE SAW IS UNPLUGGED. When cutting any material with steel blades, the most efficient depth adjustment is one that permits the blade tooth depth only to project below the bottom of the material (except when using Carbide Tipped Blades, where only y2 of the tooth tip should project bel...
Otros modelos de este manual:Jig Saw y - 97747-01 (3.35 mb)