Votos - , Puntuación media:
(
)
)
Fabricar: Craftsman
Tamaño del archivo: 1.9 mb
Nombre del archivo: 1540fd39-7f91-4379-aa89-d00aaed27b5a.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
1 11 CRRFTSMRN"TABLESAW315.228110 The following tools are needed for assembly and alignment. Note: The four hex keys listed below have been provided with your saw. The remaining tools are typical shop tools and are not included with your saw. 3/8 in. NUT DRIVER FRAMING SQUARE 'U'l'O'l'l'l'l'l,U,l,l,l,l,t, ,_rl,g,f,v,l,l,l,l,l,l,l,U,l,f. .t.l,',l,*.l.,.l,L,J.l,l.,.I,*,l.*,l,,,I.,,I,_.l.,,I.i SOCKETWRENCH WITH7/16in.SOCKET ADJUSTABLE WRENCH SCREWDRIVER #2 PHILLIPS SCREWDRIVER FLATBLADE I_ COMBINATION SQUARE 3/4in. WRENCH 3/'16in. HEXKEY,---,_-,_,_ 5/32in. HEXKEY._.._-_._._ 1/8in. HEXKEY._--__ 3/32in,HEXKEY_ _ Figure CRRFTSMRN"TABLESAW315.228110 12 Your saw is designed to perform as a versatile, _lL CAUTION: The saw blade "coasts" after the accurate, precision cutting tool that is easy to operate. saw is turned off. It is equipped with the following features for safety, ease of use, and high-quality performance: SPEED AND WIRING • a carbide tipped combination blade • a bevel indicator to set the exact angle of the blade, with locking lever • an adjustable and reversible sliding miter table • an adjustable miter fence with miter indicator • an adjustable accessory table • an adjustable rip fence with scale indicator • an adjustable riving knife (splitter) and blade guard with anti-kickback pawls • front and rear guide rails with an easy-to-read scale on front rail • a dust exhaust (2-1/2 in. hole) that can be adapted to a standard shop vacuum if desired • blade adjusting handle to set depth of cut • switch with Iockable cover plate to help prevent unauthorized use • aleg stand These features provide ease of cutting with all types of wood. _, WARNING: Before attempting to use your saw, familiarize yourself with all operating features and safety requirements. OPERATING COMPONENTS The upper portion of the blade projects up through the table, surrounded by an insert called the throat plate. To cut wood at a bevel, the blade must be tilted, using the blade adjustment handTe,scale, and bevel indicator found on the front of the cabinet. Inside the cabinet, adjustable positive stops control the degree of movement. The sliding miter table assembly is used for all crosscutting operations. The miter fence is easily adjusted to cut wood at an angle by loosening the adjusting clamp, setting the fence to the miter scale, and retightening the clamp. The sliding miter table, which rests on a base mounted on the rails, can be repositioned along the rails for wide work. It can be reversed for ripping so the projecting base is in the back. Your saw includes a rip fence and an accessory table. The accessory table can be moved from the right side of the saw to the left side as needed. The rip fence is used to position work that will be cut lengthwise. A scale on the front rail shows the distance between the rip fence and the blade. The no-load speed of your table saw is approximately 4,800 rpm. The speed will not remain constant but will be less under a load. The wiring in a shop is as important as the motor's horsepower rating. A line intended for lights only will not properly carry a power tool motor. Wire that is heavy enough for a short distance will be too light for a greater distance. A line that can support one power tool may not be able to support two or three tools. _i, WARNING: To prevent possible electrical hazards, have a qualified electrician check the line if you are not certain that it is properly wired. _i, WARNING: Observe all normal safety precautions related to avoiding electrical shock. SAFETY DEVICES Safety devices on your saw include the blade guard, the anti-kickback pawls, and the riving knife (also known as a splitter or spreader). The blade guard =sa clear strong plastic shield designed to prevent accidental contact with the blade. It also deflects any flying debris from within. _, WARNING: Although many of the illustrations in this manual are shown with the blade guard removed for clarity,do notoperate the saw withoutthe blade guard unless specifically instructedto do so. The riving knife is a metal device directly behind and above the blade. It is used to help keep the cut wood from binding together and causing possible kickback. It is very important to use the riving knife for all through- sawing operations. The anti-kickback pawls are toothed plates mounted on the riving knife. Their teeth point away from the work in case the work should be pulled back, toward the operator. Then the teeth dig into the wood to help prevent or reduce the possibility of kickback. Your saw features a receptacle on the right side of the cabinet that permits use of accessories. Use only accessories that are listed for use with this tool. When using a listed accessory, unplug the saw motor cord and use the receptacle and the saws main power switch to operate the accessory. 13 CRRFTSMRN"TABLESAW315.228110 KNOW YOUR TABLE SAW BLADEGUARD SAW BLADE REAR RAIL RIVING KNIFE MITER SCALE RIP FENCE SLIDING PAWLS_ MITERTABLE THROATPLATE...