Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
• Let tool run idle for a short time only. 4. Operation 4.1 Before initial operation • Install swivel-type air inlet. • Fit the plug nipple. 4.2 Using the tool A Caution! To ensure a long service life of this tool, it needs to be supplied with sufficient quantities of pneumatic oil. This can be achieved by: . a service unit with oiler at the compressor. . a lubricator, installed in the air line or directly on the air tool. ENGLISH . adding approx. 3-5 drops of pneumatic oil by hand every 15 minutes of use (constant operation) to the air inlet. 1. Installing or changing the saw blade. . Loosen hexagon socket screw locking the saw blade. . Insert or replace the saw blade. . Retighten hexagon socket screw. . Check to see that the saw blade is properly secured. 2. Adjusting the hoop guard: . Loosen both Phillips screws for hoop guard adjustment. . Adjust hoop guard to desired depth of cut. . Retighten both Phillips screws. 3. Adjust working pressure at the compressor (see Technical Specifications for max. permissible working pressure). 4. Connect tool with quick coupler to the air supply. 5. To start: . Push safety forward. . Press throttle fully down. 6. Hold saw at right angle to the work- piece and and apply slight pressure while cutting. A Caution! • If too much pressure is applied on the saw blade, it may overheat and break. With too little pressure there 9. Technical Specifications is no sufficient cutting capacity, resulting likewise in an overheating of the saw blade. • If the saw blade jams while cutting: . Release throttle lever immediately. . Remove cause for jamming. . Commence cutting only after saw blade has been entirely freed. 7. Release throttle lever to turn OFF. 5. Care and Maintenance A A Danger! Always disconnect from air supply before servicing. Repair and maintenance work other than described in this section must be carried out by qualified specialists only. • Check all screwed connections for tightness, tighten if necessary. • If the tool is not lubricated by a service unit or line lubricator, add 3-5 drops pneumatic oil to the air inlet every 15 minutes of use (constant operation). • Do not store tool unprotected outdoors or in damp environment. 6. Available Accessories • Pneumatic oil 0.5 litre Special lubricant for air tools, service units and line oilers. Stock-no. 090 100 8540 • Line oiler R3/8" female For fitting directly to air tools. Oil level can always be checked through sight glass. Stock-no. 090 105 4592 • Swivel-type air inlet DKG 1/4" For fitting directly to air tools. Improves tool manoeuverability. Stock-no. 090 106 0991 7. Repairs A A Danger! Repairs to air tools must be carried out by qualified specialists ONLY! Air tools in need of repair can be send to the service centre in your country. See Spare Parts List for address. Please attach a description of the fault to the air tool. 8. Environmental Protection The tool's packaging can be 100 % recycled. Worn out machines and accessories contain considerable amounts of valuable raw and plastic materials, which can be recycled. These instructions are printed on paper produced with elemental chlorine free bleaching process. Model KS 6000 Set Air consumption l/min 470 Max. permissible working pressure bar 6.3 Stroke mm 10 Number of strokes min 10000 Maximum cutting capacity, steel mm 2.91 Maximum cutting capacity, aluminium mm 3.26 Minimum hose size (inner) mm 9 Vibration (effective value of weighted acceleration) m/s2 < 9 Sound power level LWA Sound pressure level LPA dB (A) dB (A) 85 Dimensions: length x width x height mm 260 x 40 x 80 Weight kg 0.67 FRANCAIS 1. Vue d'ensemble de l'outil (fourniture a la livraison) 1 9 53 72 8 64 10 13 14 15 16 12 11 1 Lame de scie 11 Vis cruciforme pour regler 2 Etrier de protection l'etrier de protection 3 Vis cruciforme pour regler l'etrier de protection 12 Vis a six pans creux pour bloquer la lame de scie 13 5 lames de scie 24 dents 4 Boitier en plastique 14 5 lames de scie 18 dents 5 Articulation d'entree d'air rotative et basculable 1/4" 15 5 lames de scie 32 dents 16 Levier de securite 6 Logement pour embout (raccordement air comprime) Sans illustration : 7 Embout 1/4" – Mallette en plastique 8 Sortie d'air insonorisee 9 Flacon d'huile 10 Cle a six pans creux 3 mm (pour changer de lame de scie) FRANCAIS Table des Matieres 1. Vue d'ensemble de l'outil (fourniture a la livraison)..........10 2. A lire en premier !.....................11 3. Securite......................................11 3.1 Utilisation conforme aux prescriptions ...............................11 3.2 Consignes de securite generales....................................11 4. Fonctionnement........................12 4.1 Avant la premiere mise en service ........................................12 4.2 Utilisation de l'outil......................12 5. Maintenance et entretien..........12 6. Accessoires disponibles..........12 7. Reparations...............................12 8. Protection de l'environnement ........................