Iniciar sesión:
Votos - 6, Puntuación media: 3.7 ( )

Manual de usuario Attwood, modelo 4031

Fabricar: Attwood
Tamaño del archivo: 458.46 kb
Nombre del archivo: 69317-d-heavy-duty-bilge.pdf
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


Look to Attwood for quality replacement parts and marine accessories. SAVE THESE INSTRUCTIONS Form Number 69317 Rev. D 03/10 FEATURES Attwood Heavy Duty Bilge Pumps are the newest development in high output pumps. All models have a removable housing for simple installation and easy cleaning. They connect to 12-volt D.C. systems only. There are two ways to configure your Heavy Duty Bilge Pump – Automatic Operation orManual Operation. The bilge pump system can be converted to fully-automatic operation by installing the Attwood Automatic Float Switch, Part No. 4201 or 4202. AUTOMATIC OPERATION All boats over 20' (6.1 m) in length which have sleeping accommodations (excluding fold-out cockpit seats) require automatic bilge pump systems. For fully-automatic operation, follow the AUTOMATIC FLOATSWITCH INSTAL- LATIONand AUTOMATIC OPERATION WIRINGinstructions. MANUAL OPERATION For manual operation of your bilge pump system, disregard the references to Automatic Float Switch installation and operation. Check the chart below to select the proper pump, fuse size, and thru-hull connector for your boat application: Pump Part Pump Amp Outlet Hose Thru-Hull Number Model Volts Fuse Inside Dia. Connector 4030, 4031 HD1700 12VDC 10 1-1/8" (29mm) 3874 4060, 4061 HD2000 12VDC 12 1-1/8" (29mm) 3874 Recommendations are based on amount of gallons exhausted per hour (GPH). GPH measurements are typical of production pumps tested using smooth-bore hoses, at 0' head. “Head” refers to the vertical distance between the pump nozzle and the water discharge location. GPH is reduced as head is increased. The chart below shows gallons and liters per hour ratings for 0' head and 3' (91.4 cm) head. GPH/LPH may also vary depending on power source, hose type, and other variables. ABYC Specifications 13.6 volts DC (GPH=Gallons Per Hour) ISO Specifications 12.0 volts DC (LPH=Liters Per Hour) Part No. Model GPH Open Flow LPH Open Flow GPH 3' Head LPH 3' Head Amp Draw 4030, 4031 HD1700 1,700 6,450 1,300 4,920 6.0 4060, 4061 HD2000 2,000 7,600 1,550 5,867 8.0 The pumps can run dry for limited periods of time; however, doing so could cause pump failure. WARNING: To prevent personal injury, always disconnect the power source when installing or servicing any electrical product. Remove vessel from water when using any 110/120 or 220 Volt AC power tools. Doing so could result in fire, explosion, and serious personal injury. Always use the fuse amperage rating specified for your pump model. Failure to do so could result in serious personal injury or fire hazards. Attwood bilge pumps are designed to exhaust standing WATER ONLY. They are not intended to prevent rapid accumulation of on-board water due to rough weather, severe storms, hull damage, and/or other unsafe navigational conditions. Do not allow materials containing acetic acid (vinegar smell) such as silicone rubber sealant to contact the plastic parts of the pump. They may react with the plastic, causing cracks and pump failure. Notice:...

Otros modelos de este manual:
Barcos - 69317 (458.46 kb)
Barcos - 4030 (458.46 kb)
Barcos - 4060 (458.46 kb)
Barcos - 4061 (458.46 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría