Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Each of theseends on the aluminum slats have 1 big 1 1/2" hole & 4 1/8” holes surrounding the big hole as shown below. Use four 3/4” screws to attach each flush mount adapterto the aluminum slat with a phillips head screw driver. Please note, the adapters can stay attached to the slats and never need to be disassembled. Now place the rod holders in the adapters as shown. For disassembly, you only need to detach the rod holders from the flush mount adapters. On the 325fc, install the rod holders at the end of the middle aluminum slat. Oar Locks & Oars There are 2 oars and 2 oarlocks included in any of our FoldCatpackages. Each oarlock includes araised oarlock base, an oarlock pin, two bolts attached and 2 knurled nuts. On the 375fc, bolt the raised oarlock bases at both ends of the 2nd rearmost aluminum slat through the 4pre-drilled 3/8" holes (2 at each end) using knurled nuts. And then placethe oarlock pins into the raisedoarlock rods as shown. Now snap the two 8’ sectional oars together and inset each oar into the oarlock pins and tighten the wingnuts to securethe oars as shown below. On the 325fc, the raised oarlock bases are installed on the first aluminum slat in the bow. And then attach the oarlock pins and oars as explained above for 375fc. 6 Motormount Parts for the motormount include wooden motormount plate, 2aluminum L-brackets, four bolts, 4 washers and 4 knurled nuts. This rearmost slat has 2 pre-drilled 3/8" holes forplacement of motormount. Bolt the aluminum L-bracketsthrough these 2 holes by inserting the 2 bolts downthrough the front holes in the L-brackets and securing withknurled nuts below as shown. Secure the wooden motormount plate to the L-brackets byrunning the other 2 bolts through the top holes in the L- brackets and the 2 holes in the motormount plate itself. Tighten all knurled nuts and bolts. Your motormount assembly is now complete. Fully assembled Deluxe Package looks like this: SE 375fc shown Fully assembled FoldCat 375fc Pro Angler’s Package looks like this: SE 375fc shown Please note, after first time assembly of the FoldCat 325fc or 375fc, for disassembly all you have to do is deflate the air chambers, remove the underbars, swivel seats, rodholders, oars and unscrew the oarlocks.For transportation, simply roll-up the hull along with the aluminum slats & motormount and place it in the FoldCat carry bag. Canopy (for FoldCat 375fc only) Install 1 Sea Tie on the aluminum step rod in the bow of theFoldCat 375fc. Then install the other 2 Sea Ties to the last slat in the stern of the FolCat as shown. Install the two raised oarlock bases on the sides of the second wide aluminum slat from the bow as shown. 7 Insert the canopyrods with preassembled pinsinto the raised oar lock rod bases as shown. The center black strap on the canopyshould be attached to the sea tie on the aluminum step rodin the bow. Attach the other two black straps to thetwo sea ties on the last aluminum slat in the stern as shown. Fully assembled canopy should look like this Casting Bar A) Installation for FoldCat 375fc (1) Partially deflate bothpontoons and insert thebase arm of the castingbar under the first slat in the bow of the FoldCat as shown. Place the other end of the base under the step rod so that the step rod fits in the notch as shown in thenext picture. (2) Now insert thesnaplock bracket at thisend as shown. (3) Push the snaplockbracket so that the pinis snapped in position. Attach the base to the other side of the FoldCat in the same way. (4) Now raise the other ends in the vertical position so that thesnaplock pin at theelbow joint snaps inplace. (5) Now attach theupper part of thecasting bar to the raisedends till the snaplockbutton locks in place. You may adjust theheight of the casting barto the position that iscomfortable to you. B) Installation for FoldCat 325fc Partially deflate both pontoons and insert the base arm ofthe casting bar under the first slat in the bow of the FoldCat. Unlike the 375fc, on the 325fc do not attach the other end of the base to the step rod and follow steps (1), (4) & (5) only explained above for FoldCat375fc. The reason why the casting bar is not attached tothe step rod on a 325fc is because it will be too far fromthe person standing on the first slat. Casting bar on the325fc should look this this: 8 Basic Motoring Instructions The Sea Eagle FoldCat 325fc and 375fc are a very lightweight catamarans. Since only the pontoons are in touchwith water, there is less drag and so they motor very welleven with small outboard motors. They take only up to 3 HPgas engines. You can also use up to 74 lb. thrust electricmotors. As with any boat, while motoring you need to bekeenly aware of the wind and water conditions around you -especially while using an electric motor, you don’t want tobe caught with a 4 knot boat trying to fight a 5 knot tidalcurrent. As with all boating, a little planning goes a longway. However, you will be surprised at the finemaneuverability of the FoldCat...
Otros modelos de este manual:Barcos - 325FC (1.11 mb)