Votos - 5, Puntuación media: 4.2
(
)
)
|
Resumen del manual
Horn The horn button is a momentary switch. The horn will operate whenever the button is pressed and will stop when the button is released. 4-15 Section 4 12 Volt Port This receptacle can be used to power and charge cellular phones, MP3 players, video cameras or other electronics. These receptacles are powered through a 10 amp breaker. Ignition and Switch Panel NOTICECORC137 START12V Some of the switches on your boat may not have a function, based CAUTION The keypad and switch control box will be damaged beyond repair if the boat’s battery cables, the main switch control box power leads or battery charger leads are reversed. DO NOT reverse these connections. on the way the boat is equipped. Keyless Ignition The optional ignition switch system is keyless and has three modes of operation. 4-16 Correct Craft, Inc. Controls and Indicators Locked Mode When the boat’s battery is first connected, the unit is in locked mode. In this mode, only the horn, bilge pump, bilge blower and code keys operate. Unlocked Mode Unlocked mode is entered after the user successfully enters the user code, presses and releases the start key. When the code keys are pressed, the system indicator light will turn ON while the key is pressed. This indicates the key has actually been pressed. When the system is unlocked, power is supplied to the boat and the system indicator light will turn ON. At this point all keypad keys will operate and actuating these keys will control the corresponding boat functions. To put the unit back in Locked Mode, the user must successfully enter the user code, then press the STOP key. This will turn off the system indicator light and shut off power to all of the accessories except the horn, bilge pump, bilge blower and code keys. Run Mode Enter the Unlocked Mode. Pressing and releasing the START key quickly will put the unit in Run Mode. Power is supplied to the engine ignition, but the engine will not crank and the ignition indicator light is turned ON. If the start key is not pressed again within 15 minutes, the unit will exit Run Mode by shutting off power to the ignition and re-enter the Unlocked Mode. If the user presses and holds the START key, power is supplied to the ignition and starter for as long as the user presses the START key. All accessory keys will operate in this mode. Pressing the STOP key will shut off the engine and the unit is then put back in the Unlocked Mode. After the engine starts, release the START key. CAUTION DO NOT hold the START key for more than 30 seconds. The starter motor can be damaged. 4-17 Section 4 Automatic Return to Locked Mode If no keypad activity takes place for 10 hours after unlocking, the system will automatically return to the Locked Mode to help prevent battery drain. Automatic Back-lighting Pressing any keypad key will automatically turn the keypad backlighting on for 10 seconds. This feature is useful for finding the keypad at night. Multiple Keyless Ignition Codes The keyless ignition system has provisions for three different ignition codes. Any of the three codes may be used to unlock or lock the system. The “Master Embedded Code” is programmed into the system at Correct Craft Inc. It is not changeable and remains with the boat for its life. This code can be used to unlock the system, to lock the system and to erase the two user codes. The “Primary User Code” is programmed into the system by the owner with the Correct Craft Dealer’s help at the time of boat delivery. This code is used to unlock the system, to lock the system and to add or change the “Secondary User Code.” The “Secondary User Code” is programmed into the system by the owner when necessary. This code is only used to unlock or lock the system. The “Secondary User Code” is ideal to limit access to the boat. NOTICE To help prevent battery drain, make sure you STOP the engine and LOCK the PME ignition system (two steps) when you are finished using the boat. 4-18 Correct Craft, Inc. Controls and Indicators NOTICE The “System Indicator Light” is on the right side of the ignition keypad. The “Ignition Indicator Light” is on the left side of the ignition keypad. Programming the Primary User Code NOTICE Until a Primary User Code is set, the keyless ignition does not require the entry of a code to unlock the system or start the engine. This system operates as follows: 1. Press START to unlock the system. 2. Press it a second time to start the engine. 3. Press STOP to turn off the engine. 4. Press it a second time to lock the system. The system indicator light should be OFF. To program the Primary User Code, make sure the system indicator light is off, then press and release the 1/2 key and the 7/8 key at the same time to put the system in the Code Programming Mode. The system indicator light will flash. Enter a code from two to eight characters and press START. For verification, re-enter the code and press START again. The system indicator light should stop flashing and stay ON. If the light does not ...
Otros modelos de este manual:Barcos - 220 (3.96 mb)