Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
The FWDM-1629 is designed expressly for service providers deploying DWDM networking equipment in metropolitan Ethernet and SAN networks. The fiber link budget has been enhanced to 30dB with an Avalanche Photo Diode (APD) receiver. In addition, digital diagnostic features are implemented as described in Finisar Application Note AN-2030, “Digital Diagnostic Monitoring Interface for Optical Transceivers”2. O Finisar Corporation PRELIMINARY and Confidential Page 1 Rev C, February 2005 F i n i s a r PRODUCT SELECTION Product Code Frequency (THz) Center Wavelength (nm) FWDM -1629-17 191.7 1563.86 FWDM -1629-18 191.8 1563.05 FWDM -1629-19 191.9 1562.23 FWDM -1629-20 192.0 1561.42 FWDM -1629-21 192.1 1560.61 FWDM -1629-22 192.2 1559.79 FWDM -1629-23 192.3 1558.98 FWDM -1629-24 192.4 1558.17 FWDM -1629-25 192.5 1557.36 FWDM -1629-26 192.6 1556.55 FWDM -1629-27 192.7 1555.75 FWDM -1629-28 192.8 1554.94 FWDM -1629-29 192.9 1554.13 FWDM -1629-30 193.0 1553.33 FWDM -1629-31 193.1 1552.52 FWDM -1629-32 193.2 1551.72 FWDM -1629-33 193.3 1550.92 FWDM -1629-34 193.4 1550.12 FWDM -1629-35 193.5 1549.32 FWDM -1629-36 193.6 1548.51 FWDM -1629-37 193.7 1547.72 FWDM -1629-38 193.8 1546.92 FWDM -1629-39 193.9 1546.12 FWDM -1629-40 194.0 1545.32 FWDM -1629-41 194.1 1544.53 FWDM -1629-42 194.2 1543.73 FWDM -1629-43 194.3 1542.94 FWDM -1629-44 194.4 1542.14 FWDM -1629-45 194.5 1541.35 FWDM -1629-46 194.6 1540.56 FWDM -1629-47 194.7 1539.77 FWDM -1629-48 194.8 1538.98 FWDM -1629-49 194.9 1538.19 FWDM -1629-50 195.0 1537.40 FWDM -1629-51 195.1 1536.61 FWDM -1629-52 195.2 1535.82 FWDM -1629-53 195.3 1535.04 FWDM -1629-54 195.4 1534.25 FWDM -1629-55 195.5 1533.47 FWDM -1629-56 195.6 1532.68 FWDM -1629-57 195.7 1531.90 FWDM -1629-58 195.8 1531.12 FWDM -1629-59 195.9 1530.33 FWDM -1629-60 196.0 1529.55 FWDM -1629-61 196.1 1528.77 O Finisar Corporation PRELIMINARY and Confidential Page 2 Rev C, February 2005 FWDM-1629-XX DWDM SFP Preliminary Product Specification – February 2005 F i n i s a r I. Pin Descriptions Pin Symbol Name/Description Ref. 1 VEET Transmitter Ground (Common with Receiver Ground) 1 2 TFAULT Transmitter Fault 3 TDIS Transmitter Disable. Laser output disabled on high or open 2 4 MOD_DEF(2) Module Definition 2. Data line for Serial ID 3 5 MOD_DEF(1) Module Definition 1. Clock line for Serial ID 3 6 MOD_DEF(0) Module Definition 0. Grounded within the module 3 7 Rate Select No connection required 4 8 LOS Loss of Signal indication. Logic 0 indicates normal operation 5 9 VEER Receiver Ground (Common with Transmitter Ground) 1 10 VEER Receiver Ground (Common with Transmitter Ground) 1 11 VEER Receiver Ground (Common with Transmitter Ground) 1 12 RD-Receiver Inverted DATA out. AC Coupled 13 RD+ Receiver Non-inverted DATA out. AC Coupled 14 VEER Receiver Ground (Common with Transmitter Ground) 1 15 VCCR Receiver Power Supply 16 VCCT Transmitter Power Supply 17 VEET Transmitter Ground (Common with Receiver Ground) 1 18 TD+ Transmitter Non-Inverted DATA in. 100 ohm termination between TD+ and TD-, AC Coupled thereafter 19 TD-Transmitter Inverted DATA in. See TD+ 20 VEET Transmitter Ground (Common with Receiver Ground) 1 Notes: 1. Circuit ground is internally isolated from chassis ground. 2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V. 3. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 5.5V. MOD_DEF(0) pulls line low to indicate module is plugged in. 4. Finisar 2x receiver achieves simultaneous 1x and 2x operation without active control. 5. LOS is open collector output. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 5.5V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. Towards Bezel 1 VeeT 2 TXFault 3 TX Disable 4 MOD-DEF(2) 5 MOD-DEF(1) 6 MOD-DEF(0) 7 Rate Select 8 LOS 9 VeeR 10 VeeR VeeT 20 TD19 TD+ 18 VeeT 17 VccT 16 VccR 15 VeeR 14 RD+ 13 RD12 VeeR 11 Towards ASIC O Finisar Corporation PRELIMINARY and Confidential Page 3 Rev C, February 2005 FWDM-1629-XX DWDM SFP Preliminary Product Specification – February 2005 F i n i s a r Diagram of Host Board Connector Block Pin Numbers and Names II. Absolute Maximum Ratings Parameter Symbol Min Typ Max Unit Ref. Maximum Supply Voltage Vcc -0.5 4.7 V Storage Temperature TS -10 85 °C Case Operating Temperature TOP -5 70 °C III. Electrical Characteristics (TOP = -5 to 70 °C, VCC = 3.13 to 3.50 Volts) Parameter Symbol Min Typ Max Unit Ref. Supply Voltage Vcc 3.13 3.30 3.50 V Supply Current Icc 305 mA Inrush Current Isurge Icc+30 mA Maximum Power Pmax 1.0 W TRANSMITTER Input differential impedance Rin 100 W 1 Single ended data input swing Vin,pp 250 1200 mV Transmit Disable Voltage VD Vcc – 1.3 Vcc V Transmit Enable Voltage VEN Vee Vee+ 0.8 V 2 RECEIVER Single ended data output swing Vout,pp 175 1000 mV 3 Data output rise time tr 150 ps 4 Data output fall time tf 150 ps 4 LOS Fault VLOSfault Vcc – 0.5 VccHOST V 5 LOS Normal VLOS norm Vee Vee+0.5 V 5 Power Supply Rejection PSR 10...