Votos - 6, Puntuación media: 4
(
)
)
|
Resumen del manual
(consult a qualified technician for instructions) • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started • Remove 2 transit screws located on top of the unit. Cover transit screw holes using the supplied adhesive dot labels. • Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve. • Install mounting sleeve into opening, bending tabs to secure. • Connect wiring harness and antenna. (consult a qualified technician if you are unsure) • Test for correct operation and slide into mounting sleeve to secure. • Snap trim ring into place. • Mount the iplug™ adapter to any smooth clean surface using the supplied double-sided tape or #2 x 3/8” Phillips head screws. MXDM70 INSTALLATION Wiring Diagram FUSE When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The MXDM70 uses one10 amp ATM fuse located beside the wiring connector. MWR30 Wired Remote (sold seperately) MXDM70 OPERATION Control Locations 21222019181716151413121112345678910 1234567891011 Release Power Volume Band/Play/Pause Mode/Search Auto Store/Preset Scan/Enter Tune/Track Down Eject Tune/Track Up Display/ 0 EQ/ 9 1213141516171819202122 Tuner Scan/ 8 Local/Distance/ 7 Preset 6/Folder Up Preset 5/Folder Down Preset 4 Preset 3/Intro Preset 2/Random Preset 1/Repeat Audio Loudness Mute The MXDM70 allows playback of your favorite MP3 and WMA files recorded on CD-R and CD-RW discs. Its powerful on-board DSP processor decodes the compressed audio while maintaining near-CD sound quality. An internal SRAM buffer provides ESP (Electronic Skip Protection) to virtually eliminate skipping and allows alphanumeric or direct track search - even while a song is currently playing! MXDM70 OPERATION General Operation Faceplate Removal Press RELEASE and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure. Semi-permanent Faceplate Installation Remove trim ring and install supplied #1 x 7/32” Phillips head screw through left side of mounting frame into faceplate. Power On/Off Press POWER or any other button (except eject) to turn the unit on. Inserting a disc will turn the unit on automatically. Press POWER to turn the unit off. Mode Press MODE to select between tuner, weatherband tuner, CD player and auxiliary input. Modes of operation are indicated in the display. Loudness Press LOUD to activate and deactivate the loudness contour curve. Activating this feature will enhance the bass and treble frequencies when listening to music at low volumes. Volume Adjust volume using rotary encoder (00-46). Programmable Turn-On Volume Press and hold POWER for 3 seconds to program currently selected volume level. "P-VOL" and the current volume level will momentarily appear in the display. Preset EQ Curves Press EQ to select between POP, JAZZ, CLASSIC, BEAT, ROCK and OFF (default) equalization curves. Any adjustment to the Bass or Treble settings automatically cancels the current EQ curve (if one is selected). Display Press DISP to select between clock and radio frequency (tuner mode), clock and CD track/elapsed time (CD mode), or clock and AUX (AUX mode). Set the Clock With the unit on, press and hold DISP until the clock begins to flash, then release. Press TUNE nn to adjust the hours and TUNE ll to adjust the minutes. Press DISP momentarily to save the selected time. MXDM70 OPERATION General Operation 12/24-hour Clock Programmable Display Priority Programmable Clock Priority Reset Confirmation Beep Mute The clock will display 12-hour AM/PM time in USA frequency spacing mode (PM 10:00). In European frequency spacing mode, the clock will display 24-hour time (22:00). In tuner mode, press and hold DISP then press TUNE ll to select function priority display. “FREQ” will momentarily appear in the display. Note: "FUNC" will appear in CD or AUX modes. Radio frequency (tuner mode), CD track/elapsed time (CD mode) or AUX (AUX mode) will be displayed by default. Note: When playing MP3/WMA files, the track number/elapsed time, track name, directory name, title, artist, album, year or comment will be displayed by default. Clock is accessed by pressing DISP momentarily. Press and hold DISP then press TUNE nn to select time display priority. “TIME” will momentarily appear in the display. Clock will be displayed by default. Radio frequency, CD track/elapsed time or MP3/WMA file information is accessed by pressing DISP momentarily. Programs unit to display clock/no clock when unit is off. Press and hold MODE then press PRESET 1 to select clock priority on/off. “CLK ON” or “CLK OFF” will momentarily appear in the display. Press and hold for more than 2 seconds to RESET the unit upon initial installation or if abnormal operation occurs. The reset button is located behind the faceplate. Press and...