Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Do not allow the battery to charge for greater than 1 5 hours. The useful life and battery performance will be reduced if you exceed the recommended charge period. NOTES:-— • Turn off the power switch before charging. • Recharging should be done within an ambient temperature between 10°C~40°C (50°F~ 104°F). Recharging performed out of this range may not fully charge the battery. MANGANESE or ALKALINE BATTERIES Load 6 x R6 (AA) manganese or alkaline batteries in series in the supplied battery case. (Be sure to observe the polarities.) (We recommend use of high-perfomance manganese batteries.) Battery pack (1) can be inserted into the case (2) only in a specific direction. Check the shape (top and bottom) after moving the stopper on the rear side, then insert the battery correctly. Inserting the battery by force without checking the shape may damage the case. OPERATING TIME Case (2) Battery pack ( 1 ) ^tSlbauer^soOmAh Transmitting...............................1 minute Receiving.................................3 minutes AF OUTPUT...........................0.35 W/8 0 “Battery voltage is measured at transmission (Hi). Ni-Cd battery 7.2V !800mAh KPB-3) ВАТТЛ lit voltage indicator _^al|ne man9anisetbattery~ ( ( ^ar>gan^se~batte^~ Lower ''m't volta9e range for transmission I 120 240 Manganese battery (except Alkaline manganese battery) is suitable only for LOW power transmission. Recharge the Ni-Cd battery pack when the BATT indicator comes on. We recommend use of the PB-3 or PB-4 Ni-Cd battery pack for long transmission or extended operation. CONTROLS AND FUNCTIONS ©Antenna connector This jack is used to connect the supplied antenna. Twist to lock with the BNC connector. This terminal is used for an external power supply. Input voltage is 13.8 VDC nominal. The center is the ( + ) side and the sleeve is (-) side. You should turn the power switch OFF when connecting this terminal. Pay attention to the polarity. This jack is used for connection of an external microphone. The use of an electret type microphone is recommended. Input impedance is 2 kil and the DC voltage on this terminal is 4 V. This jack is used for an earphone or external speaker. The recommended impedance is 8 Q nominal. © DC IN terminal CAUTION: As a precaution, do not remove the battery pack when an external power supply is used. Use the KENWOOD PG-2V (supplied with the U.S.A version) or PG-3D optional cable for the connection. © MIC jack ®SP jack ©TONE switch U.S. version: This switch is used to activate the sub-audible tone encoder. 6 © (2) (D European version: This switch is used to transmit a TONE signal. When the switch is pressed the repeater control signal of 1 750 Hz is activated. ©HI ( JL )/LOW ( - )switch This switch is used to select the transmit output power. © SQL control The SQL control is used to eliminate noise during no signal periods. Normally, this control is adjusted clockwise until the noise just disappears and the BUSY indicator goes OFF (Threshold level). For scan operation, this control must be set to the threshold point. When an incoming signal is weak or unstable, readjust the squelch for optimum reception. For tone squelch operation with TSU-4, this control must be set to the T.SQ position. (TH-41 5A/31 5A/21 5A) ® VOL control Volume control with power ON/OFF switch. ® MONITOR switch Pressing this key will open squelch. @ PTT (Push To Talk) switch For transmission, press this switch and speak into the microphone. © RELEASE button Used to release the battery. Depress this button, and turn the battery counterclockwise. @ LAMP key This key controls the lamp on the LCD display. NOTE:- When the LAMP is on battery drain will be accelerated. Do not use this feature unnecessarily. ® OFFSET/F key The OFFSET/F key is used to select the desired transmitter offset for repeater operation. Each time the key is pressed, the mode cycles from + shift, to — shift, to simplex, and back to + shift. When the offset function is ON, the symbol " + " or " —" is displayed. Pressing the f and the OFFSET/F key in order is used to change the desired offset frequency. ®) R/TONE. F (or REVERSE) key This key is used to reverse the transmit/receive frequencies during repeater operation. TONE. F: TONE FRQUENCY key (with the TH-415A/215A) Pressing the [El j and the R/TONE. F key in order is used to change the frequency of the tone encoder. © SAVE key The SAVE key is used to select the power save condition during the receive mode. Pressing the Of and the SAVE key in order is used to change the battery saver on/off ratio. ® SPEAKER © MICROPHONE @ BATTERY CASE 7 QD Display ®(D (D 0 0© (8> (D- □ MW □00 a 00 TjHiM--RH V 0(0)© iPRIOl [AUTO/ /saveI IbusyI ION AIRl o O O O O O r = u U U.U U LJ.D — BAND I MEMO PROG |KEYLOCK SEEK I TIME I CAR ITX STOP I 25 20 15 ■10 5 l^tl © (B> © © -0 0 FREQUENCY display : Displays the operating frequency. (2) [PRiol : ON when the Priori...
Otros modelos de este manual:equipamiento barco - TH-215A (12.16 mb)
equipamiento barco - TH-315A (12.16 mb)
equipamiento barco - TH-415A (12.16 mb)
equipamiento barco - TH-415E (12.16 mb)