Votos - 3, Puntuación media: 4.3 ( )

Fabricar: Icom Tamaño del archivo: 3.69 mb Nombre del archivo: Idioma del manual:

• Transmitting Top panel Loosely couple a frequency counter to the antenna connector. 174.000000 MHz I/O Check window CS-F3060 ADJ I/O Check Input Dec Hex Data VIN 0 0 o.oov TEMPS 0 0 LVIN 0 0 o.oov SD 0 0 o.oov 1 O utput Data BPF T1 0 0 O.OOV T2/PWR 0 0 O.OOV TX LVA 0 0 O.OOV RX LVA 0 0 O.OOV REF 0 0 O.OOV MOD BAL 0 0 0.00% DEV 0 0 O.OOV CTCSS 0 0 O.OOV SQL Level 0 0 0.00% Update(F5) OK Lock voltage 6 - 4 6-3 TRANSMIT ADJUSTMENT Select an adjustment item using [t] / [I] keys, then set to the specified value using [^] / [^] keys on the connected PC's keyboard. ADJUSTMENT ADJUSTMENT CONDITION MEASUREMENT VALUE UNIT OPERATION OUTPUT POWER [Power (Hi)] 1 • Channel : • Transmitting CH 3 Top panel Connect an RF power meter to the antenna connector. 5.0 W [Power (L2)] 2 • Channel : • Transmitting CH 4 2.0 W [Power (L1)] 3 • Channel : • Transmitting CH 5 1.0 W MODULATION BALANCE [BAL (Narrow)] 1 • Channel : CH 13 • Preset [MOD Narrow] : 60 • No audio applied to the JIG cable. • Set an FM deviation meter same as; HPF :OFF LPF : 20 kHz De-emphasis : OFF Detector : (P-P)/2 • Push [P0] key while transmitting. Top panel Connect the FM deviation meter to the antenna connector through an attenuator. Set to square wave form FM DEVIATION (NARROW) [MOD N C] 1 • Channel : CH 13 • Connect an audio generator to the JIG cable and set as; Frequency : 1.0 kHz Level : 150 mV rms • Set the FM deviation meter to same condition as "MODULATION BALANCE." • Transmitting Top panel Connect the FM deviation meter to the antenna connector through an attenuator. ±2.05 to ±2.15 kHz (NARROW) [MOD N L] 2 • Channel : • Transmitting CH 8 (NARROW) [MOD N H] 3 • Channel : • Transmitting CH 1 (WIDE) [MOD W C] 4 • Channel : • Transmitting CH 5 ±4.05 to ±4.15 kHz (WIDE) [MOD W L] 5 • Channel : • Transmitting CH 6 (WIDE) [MOD W H] 6 • Channel : • Transmitting CH 7 (MIDDLE)1 [MOD M C] 7 • Channel : • Transmitting CH 14 ±3.15 to ±3.25 kHz (MIDDLE)* [MOD M L] 8 • Channel : • Transmitting CH 15 (MIDDLE)* [MOD M H] 9 • Channel : • Transmitting CH 16 DIGITAL 1 • Preset [Digital Mode] 7 Top Connect an FM deviation meter to ±1.41 to ±1.45 kHz DEVIATION* [MOD D C] 2 • Channel : CH 9 • Set the FM deviation meter to same condition as "MODULATION BALANCE." • Transmitting panel the antenna connector through an attenuator. [MOD D L] 3 • Channel : • Transmitting CH 10 [MOD D H] 4 • Channel : • Transmitting CH 11 CTCSS/DTCS DEVIATION [CTCSS/DTCS] 1 • Channel : CH 12 • No audio applied to the JIG cable. • Set the FM deviation meter to same condition as "MODULATION BALANCE." • Transmitting Top panel Connect an FM deviation meter to the antenna connector through an attenuator. ±0.68 to ±0.72 kHz +; [EUR-01] only. *; Necessary only when the optional UT-119 is installed. 6 - 5 6-4 RECEIVE ADJUSTMENT Select an adjustment item using [t] / [I] keys, then set to the specified value using [^] / [^] keys on the connected PC's keyboard. ADJUSTMENT ADJUSTMENT CONDITION MEASUREMENT VALUE UNIT LOCATION RECEIVE SENSITIVITY [BPF T1 C] [BPF T2 C] NOTE: "RECEIVE SENSITIVITY" must be adjusted before "S-METER." Otherwise, "S-METER" will not be adjusted properly. 1 • Channel : CH 5 • Connect the SSG to the antenna connector and set as; Frequency : 155.000 MHz Level : +20 dB|/ (-87 dBm) Modulation : 1 kHz Deviation : ±3.5 kHz • Receiving Multi connec- tor Connect the SINAD meter with an 8 Q load to the JIG cable. Minimum distortion level [BPF T1 H] [BPF T2 H] 2 • Channel : CH 6 Frequency : 136.000 MHz • Receiving [BPF T1 L] [BPF T2 L] 3 • Channel : CH 7 Frequency : 174.000 MHz • Receiving CONVENIENT: The "RECEIVE SENSITIVITY" can be adjustment automatically. 1: Put the cursor on "BPF T1 C/L/H ALL" or "BPF T2 C/L/H ALL" and then push [ENTER] key. 2: The connected PC tunes BPF's to peak levels automaticaly. or 1: Put the cursor on the one of "BPF T1 C/L/H" and "BPF T2 C/L/H" as desired. 2: Push [ENTER] key to start tuning. 3: Repeat 1 and 2 to perform additional BPF tuning. S-METER [RSSI] 1 • Channel : CH 6 • Connect the SSG to the antenna connector and set as; Frequency : 136.000 MHz Level : +23 dB|/ (-84 dBm) Modulation : 1 kHz Deviation : ±3.5 kHz • Receiving Push the [ENTER] key on the connected PC's keyboard to set "S3" level. 2 • Set the SSG as; Level : -7dB|t (-114 dBm) • Receiving Push the [ENTER] key on the connected PC's keyboard to set "S1" level. SQUELCH [SQL] 1 • Channel : CH 5 • Close the squelch by adjusting the value of [SQL] item on the CS-F3060 ADJ's screen. • Connect the SSG to the antenna connector and set as; Frequency : 155.000 MHz Level : -14 dB|t (-121 dBm) Modulation : 1 kHz Deviation : ±3.5 kHz • Receiving External speaker Connect an 8 Q speaker to the JIG cable. Set the [SQL] to the value that the audio signals just appears. t; The output level of the standard signal generator (SSG) is indicated as the SSG's open circuit. 6 - 6 ...

Descargar ahora

Introduzca dos números de la imagen: