Votos - 3, Puntuación media: 4.3 ( )

Fabricar: Desa Tamaño del archivo: 3.76 mb Nombre del archivo: Idioma del manual:

Correct all leaks at once. WARNING: Never use an open flame to check for a leak. Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. Correct all leaks at once. Pressure Testing Gas Supply Piping System Test Pressures In Excess Of 1/2 PSIG (3.5 kPa) 1. Disconnect log set and its individual equipment shutoff valve from gas supply piping system. 2. Cap off open end of gas pipe where equipment shutoff valve was connected. 3. Pressurize supply piping system by either using compressed air or opening main gas valve located on or near gas meter. 4. Check all joints of gas supply piping system.Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. 5. Correct all leaks at once. 6. Reconnect log set and equipment shutoff valve to gas supply. Check reconnected fittings for leaks. Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa) 1. Close equipment shutoff valve (see Figure 5). 2. Pressurize supply piping system by either using compressed air or opening main gas valve located on or near gas meter. 3. Check all joints from gas meter to equipment shutoff valve (see Figure 5). Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. 4. Correct all leaks at once. Equipment Shutoff Valve Gas Meter Figure 5 - Checking Gas Joints HEARTH PAN INSTALLATION If using propane/LP gas, see Propane/LP Gas Conversion before installing hearth pan. 1. Place the burner pan assembly in the center of the fireplace floor. Make sure the front of pan faces forward. 2. Thread the gas supply fitting to the fireplace gas supply pipe. Adjust to most convenient position. 3. Install the gas connector tube to the gas supply fitting. Carefully shape tube to attach to inlet fitting. Be careful not to cause kinks in tube. 4. Test for leaks following instructions under Testing Burner for Leaks, page 8. 5. Retighten and adjust the location of the gas control as necessary. The gas control should be level, with the control rod to the front. Gas Connector Tube Regulator Gas Control Valve Figure 6 - Installing Inlet Fitting and Gas Connector Tube (Valve Cover Removed for Clarity) Propane/LP Gas Conversion To convert to propane/LP gas, the burner inlet fitting and pilot orifice must be replaced and the regulator pressure must be reset. The propane/LP burner inlet fitting is supplied with the orifice installed. The propane/LP pilot orifice for converting the pilot is supplied and is marked with a red stripe. 1. Remove control rod extension and piezo ignitor by pulling gently. 2. Remove screws that attach pilot assembly to valve cover and valve cover to burner pan (see Figure 7, page 7). 3. Remove valve cover. For more information, visit more information, visit 901268-01D 901268-01D 77 Forr morre iinfforrmattiion,, viisiitt INSTALLATION Hearth Pan Installation (Cont.) INSTALLATION Continued Control Rod Piezo Ignitor Extension Screw Valve Cover Control Knob Figure 7 - Removing/Installing Cover, Control Knob, and Piezo Ignitor Thermocouple Ignitor Pilot Figure 8- Remove Burner Inlet Fitting Burner Inlet Fitting for Natural Gas Figure 9 - Burner Inlet Fittings with Injectors NATURAL GAS FITTING PROPANE/LP GAS FITTING Injector for Natural Gas Injector for Propane/LP Gas Figure 10 - Adjusting Regulator Pressure for Conversion Reversed Plastic Pressure Button for Propane/LP Conversion Plastic Pressure Button Positioned for Natural Gas Regulator Brass Plug 4. Using a wrench, remove gas control valve and burner inlet fitting by turning counterclockwise (see Figure 8). 5. Remove the burner inlet fitting from the gas control assembly (see Figure 8). DO NOT remove the orifice from this fitting. The propane/LP burner inlet fitting is included in the hardware kit (see Figure 9). 6. Be sure to use the correct orifice for your appliance. The orifice kit included with this appliance contains an orifice installed in an air mixer fitting. 7. Using thread...

Descargar ahora

Introduzca dos números de la imagen: