Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
The deckmount light and standby LED on the hand held will both blink, the autopilot system is in a start-up mode and no operations are available for 30 seconds. How to engage Autopilot: When the STBY LED turns solid press the bull’s eye and release to engage the autopilot. When the AUTO LED is solid the autopilot is engaged. Press and hold the left straight arrow button to make a port turn, AUTO LED will start blinking, to stop turn release button, AUTO LED will revert to solid when a new heading is captured. Or momentarily press button to make a 1 degree heading change. (Momentarily pressing the button twice = 2 degree change, three times = 3 degree change, etc.) Press and hold the right straight arrow button to make a starboard turn, AUTO LED will start blinking, to stop turn release button, AUTO LED will revert to solid when a new heading is captured. Or momentarily press button to make a 1 degree heading change. (Momentarily pressing the button twice = 2 degree change, three times = 3 degree change, etc.) 2 How to adjust throttle: Throttle up button, press and hold for large RPM changes or momentarily press for small RPM changes. LED in upper left will illuminate every time button is pressed. Throttle down button, press and hold for large RPM change or momentarily press for small RPM changes. LED in lower left will illuminate every time button is pressed The next two basic operations are factory defaults and may be changed by user at any time using the feature operation changes. Pushing and releasing the Idle/Resume button will cause the motor to go to idle. Press and release the button again and the motor will return to its previous RPM setting. To use this button as a MOB (man overboard) or Zig-Zags see page 4. Bent Arrow Buttons are programmed from the factory for Remote Steering. No Heading hold operations are available while using this feature. If you wish to program the bent arrows for Step Turns or Circles, see page 4. When the button is pressed the LED next to 6 will come on, the system will drop out of autopilot and put you in a port remote turn. To return to autopilot press and release the left straight arrow button. When the button is pressed the LED next to 9 will come on, the system will drop out of autopilot and put you in a starboard remote turn. To return to autopilot press and release the right straight arrow button. 3 Feature Operations (Pattern Steering) How to Select Feature Operations 1. Autopilot must be in Heading Hold or Standby Mode before selection process can start. (AUTO LED solid on or STBY LED solid on. No other LED’s on.) 2. Press and hold the Setup Button. Two LED’s next to number 1 through 6 will illuminate, indicating which special functions are programmed to operate. 3. Make selection of the Special Function you want to use by pressing and releasing the Special Function buttons until the appropriate LED’s are lit. (See Table below for Special Function Indicators.) 4. Release the Setup Button 5. To make the selected Special Functions into startup defaults (Save The Setting): Press and release the setup button, (LED will light) next press and hold the Select Load Button, then press and release the DeckMount Button quickly, last release the Select Load Button. (You can change this default by repeating this process.) Number 7, 8 and 9 are GPS features and only work when coupled with GPS (See your owner’s manual) Press and hold to change feature options. Man Over Board GPS Idle/Resume Reverse Zig-Zag patterns Step Turns to Port Step Turns to Starboard Circle Turns to Starboard Circle Turns to Port Remote Turn to Starboard Remote Turn to Port LED’s Bright or Turn back light on Dim or off Special Function Indicator LED Numbers 1 MOB 4 Steps 7 Orbit Wpt. 2 Idle/Resume 5 Circles 8 Three Leaf Clover 3 Zig-Zag (other) 6 Remote Steer 9 Search 4 How to Setup Steering Patterns (No GPS required) The following will lead through the following features step by step, Reverse, MOB, Idle/Resume, Zig- Zags, Step Turns, Circles and Remote Steer. Reverse: The Autopilot will attempt to perform any of it’s steering functions when the boat is backing in reverse gear. To engage the system in reverse; 1) Motor must me in reverse 2) Start from Standby 3) Press and hold the GPS (Rev) button 4) Press and release the Auto/STBY 5) Release the GPS (Rev) button. The reverse LED will stay lit until you go to Standby mode. MOB: 1) Press and hold Setup button 2) Select and light up number 1 on handheld 3) Release Setup button. When you want to do a MOB turn, press the Idle/Resume button once and it will make the turn. When the maneuver is over the LED will go out. Remember if you want to use the Idle/Resume you will need to change it back. Idle/Resume: The Idle/Resume is set as default from the factory. If you need to change it back from MOB or Zig-Zags; 1) Press and hold setup button 2) Select and light up number 2 on the handheld 3) Release Setup button. Now when you press and release the Idle/Resume butt...