Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
Electronic fuel injection, anti-skid braking, and cruise control systems are typical examples of equipment that may malfunction. If your vehicle contains such equipment, consult the dealer for the make of vehicle and enlist his/her aid in determining if they will perform normally while transmitting. PREPARATION PREPARATION Note: The following preparation instructions are for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory. TOOLS REQUIRED Note: Before installing the transceiver, always check how far the mounting screws will extend below the mounting surface. When drilling mounting holes, be careful not to damage vehicle wiring or parts. The following tools are required for installing the transceiver: • 1/4 inch (6 mm) or larger electric drill • 5/32 inch (4.2 mm) drill bit for the self-tapping screws used to mount the optional mounting bracket • Circle cutters POWER CABLE CONNECTION . The transceiver operates in 12 V negative ground systems only! Check the battery polarity and voltage of the vehicle before installing the transceiver. . Use only a KENWOOD optional DC power cable. . Do not cut and/or remove the fuse holder on the DC power cable. 1 Check for an existing hole, conveniently located in the firewall, where a power cable can be passed through. If no hole exists, use a circle cutter to drill the firewall, then install a rubber grommet. 2 Run the two power cable leads through the firewall and into the engine compartment, from the passenger compartment. 3 Connect the red lead to the positive (+) battery terminal and the black lead to the negative (.) battery terminal. • Locate the fuse as close to the battery as possible. 4 Coil and secure the surplus cable with a retaining band. • Be sure to leave enough slack in the cables so the transceiver can be removed for servicing while keeping the power applied. 2 INSTALLING THE TRANSCEIVER For passenger safety, install the transceiver securely using an optional mounting bracket and screw set so the transceiver will not break loose in the event of a collision. 1 Mark the position of the holes in the dash by using the mounting bracket as a template. Drill the holes, then attach the mounting bracket using self-tapping screws. • Be sure to mount the transceiver in a location where the controls are within easy reach of the user and where there is sufficient space at the rear of the transceiver for cable connections. 2 Connect the antenna and power cable to the transceiver. 3 Slide the transceiver into the mounting bracket and secure it using hex-headed screws. 4 Mount a microphone hanger in a location where it will be within easy reach of the user yet not interfere with the safe operation of the vehicle. When replacing the fuse in the DC power cable, be sure to replace it with a fuse of the same value. Never replace a fuse with a fuse that has a higher value. Hex-headed screws DC power cable Mounting bracket Antenna connector Power input connector Fuse holderBlack (.) cable Red (+) cable 12 V vehicle battery Microphone Microphone hanger Short plug Fuse Hex-headed screw Ground lead (commercially available) * The TK-5710 is shown in the above diagram. Note: The items above shown in gray are optional accessories. 3 GETTING ACQUAINTED GETTING ACQUAINTED KCH-14 (BASIC CONTROL PANEL) GRP VOL CH POWER TX BUSY qwrte yuio !0 !0 q qqqqqPower switch Press to switch the transceiver ON. Press and hold for approximately 1 second to switch the transceiver OFF. w wwwwwGRP key Press to increase the zone number. Also press to increase setting adjustments. e eeeeeGRP key Press to decrease the zone number. Also press to decrease setting adjustments. r rrrrrDisplay Refer to page 5. t tttttSpeaker Internal speaker. y yyyyyTX and BUSY indicators The TX indicator lights red while transmitting. The BUSY indicator lights green while receiving. u uuuuuMicrophone jack Insert the microphone plug into this jack. i iiiiiVOL (Volume) control Rotate clockwise to increase the volume level. Rotate counterclockwise to decrease the volume level. o oooooCH (Channel) control Rotate clockwise to increase the channel number. Rotate counterclockwise to decrease the channel number. Your dealer can also enable the CH control to be used when making setting adjustments, as an optional method for using the GRP and GRP keys. ! !!!!!0 0000 00PF 1 ~ PF 5 (Programmable Function) keys Press to activate their programmable functions {page 9}. 4 KCH-14 DISPLAY rotacidnInoitpircseDdnaenozrosrebmunlennahcdnaenozgnitarepoehtsyalpsiDsegassemtxetsuoiravsyalpsidoslA.semanlennahc.desugniebnoitcnufehtnognidnepedoslA.srebmunlennahcdnaenozgnitarepoehtsyalpsiDgnidnepedsretcarahcsuoiravdnasrebmuntsilTSOsyalpsid.desugniebnoitcnufehtno.gnilangislanoitpognisusillacdevieceranehwsraeppAehtnehwdnaevitcasinoitcnufrotinoMnehwsraeppA.neposihcleuqsreviecsnart.edomnacSgnisuerauoynehwsraeppA.detavitcasinoitcnufrekaepslanretxeehtnehwsraeppAsinoitcnufnoitpyrcnErorelbmarcSehtnehwsraeppA.detavitca.detavitcaneeb...
Otros modelos de este manual:equipamiento barco - APCO P25 TK-5710H (387.87 kb)