Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
The toner cartridge carrier rotates and then stops. After confirming the Insert Black Toner (K) message, open the front door. Hold the tape on the protective cover and gently pull it forward to remove the cover from each cartridge slot. You only have to remove the cover from each toner cartridge slot the first time you use your printer. Toner will be present on the roller. Make sure the color of the toner cartridge matches the slot on the toner cartridge carrier. The order is K, Y, M, C. Gently shake the cartridge to distribute the toner evenly. Lift the tab up 90 degrees and pull the toner seal straight off, keeping it parallel with the toner cartridge. To insert the toner cartridge, face the label on the cartridge to the front and align it with the arrows on the printer. Guide the cartridge until it snaps into place and then push down the handhold to lock the cartridge in place. Close the front door. The toner cartridge carrier rotates to the next empty slot. When the color of the newly inserted cartridge appears on the display, followed by the Insert message, insert the next toner cartridge. Repeat steps 6-11 until all cartridges are installed. Open the front door, then lift and push back the top cover. Take the drum cartridge out of the box, and then remove the protective sheet. To insert the drum cartridge, push up the lever on the right side of the printer. Setting Up Your Printer | 1 Unpack the printer and tray module. Remove any tape from the printer and tray module, and remove the protective seal from the operator panel. For the Dell Laser Printer 3000cn, the part marked with in the above illustration is not provided with the printer. To install the standard tray module, place the tray module on top of the table or printer cabinet where you plan to use the printer. The three tabs, round peg thumbscrews, and square holes help you position the tray module so the edges are aligned properly. Set the printer on top of the tray module. Make sure the printer is securely in place. For the Dell Laser Printer 3000cn, the procedures in step 2 and 3 are required if you purchase the optional 250-sheet tray module. Remove the tray. There are two knobs located under the top plate of the tray module. Reach into the tray module and push up the knobs once, then turn the knobs counterclockwise as illustrated to attach the tray module to the printer. Open the front door, remove the spacer, and then close the front door. 2 3 4 5 CAUTION: The printer requires at least two people to lift it safely. 6 7 9 10 11 8 12 13 14 Continued to back page / . CAUTION: When removing the toner seal, a small amount of toner leakage could occur. CAUTION: Before you set up and operate your Dell™ printer, read and follow the safety instructions in your Owner’s Manual. • These instructions and illustrations are based on Dell Laser Printer 3100cn. • The standard 250-sheet tray module is only available for Dell Laser Printer 3100cn. The procedures in steps 2 and 3 are not required for Dell Laser Printer 3000cn. • The optional multi protocol card is only available for Dell Laser Printer 3100cn. • The tray module in steps 17 through 21 is optional for Dell Laser Printer 3000cn. T6131A00 Slide the width guides to the edge of the tray. The width guides should be fully extended. Squeeze the length guide and slide it to the edge of the tray. Load the paper in the tray, making sure the paper does not go above the maximum fill line. Slide the width and length guides against the edge of the paper. Insert the tray. On the operator panel, press the up/down arrow buttons, if necessary, to change the size and type of paper loaded in your printer. When you find the correct size/type, press . When you do not use the optional tray with the Dell Laser Printer 3000cn, load the paper in the multipurpose feeder. Before printing a document, make sure the paper extender is fully extended. Connect your printer to a computer or network. Click Cancel on any New Hardware screens if they appear. 16 When using a USB cable When using an Ethernet cable When using a parallel cable 17 18 19 20 21 22 Managing Your Printer From the Web | Managing your printer from the web is only available if your printer is connected to a network. Network printing is even easier with the Dell Printer Configuration WebTool. After proper configuration, the E-Mail Alert Setup feature emails you when toner and paper supplies are running low, or when the printer needs attention. The Copy Printer Settings feature lets you quickly and easily copy your 3100cn printer’s settings to another printer. To launch the Dell Printer Configuration Web Tool, type your network printer IP address in your Web browser. If you don’t know your printer IP address, print a Printer Settings page. For more information on managing your printer from the web, see your User’s Guide. If the IP address shows 0.0.0.0 under the TCP/IP heading, you need to assign an address to the printer. See your Owner’s Manual for instructio...