Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
We are confident that you will find satisfaction in the high quality sound and top performance, and that you will find pleasure in the functional beauty achieved through human-engineering concept. Before starting operation, please read this instruction manual thoroughly and acquaint yourself with the proper mode of using the unit and all its connections. We hope you will enjoy top-notch performance for many years to come. INSTALLATION Be sure to place the unit in a level and flat place where it is free from humidity, vibration, high temperature and not exposed to direct sunlight. Be careful not to place the unit in a highly enclosed place such as near a wall or on a bookshelf. A poor ventilation will cause undesirable effects to the unit. CASSETTE TAPES • To prevent possible trouble with the transport mechanism, use of large size cassette tapes, such as C-120, is not recommended. • Handle cassette tapes with care. Keep them away from heat, circulating dust, or a magnetic field (e.g. on the TV set). • Each cassette tape has safety tabs on its back edge to prevent accidental re-recording. The tabs are provided for both sides of cassette tape. You cannot record on the side whose tab has been removed. The tab can be removed with a screwdriver, etc. If you wish to record on the side with no tab. place a piece of adhesive tape, etc. over the opening where the tab has been, then you can record. AUTOMATIC SHUTOFF SYSTEM To protect the RMD-82 motor and transport mechanism against unnecessary wear, an automatic shutoff device has been built into the unit. When either end of tape is reached in play, record, fast-forward, or rewind mode, the motor and mechanism will automatically shut off. disengaging the present mode. POWER SUPPLY The RMD-82 is designed to receive power only through the special power supply socket on the rear panel of the ROTEL receiver RMX-82. Plug the power cord of the RMD-82 into the power supply socket of the RMX-82. Never attempt to connect the RMD-82 power cord to a wall outlet or convenience outlet in other audio components. CONNECTION TO RECEIVER RMX-82 Two pairs of RCA cords for LINE IN/OUT extend out from the rear panel of the cassette deck. The cord from the LINE IN terminals of the deck should be plugged into the TAPE MONITOR OUT terminal of the RMX-82. and the cord from LINE OUT terminal to the TAPE MONITOR IN terminal. RCA cords with white plugs are for left channel (L) connection, and cords with red plugs are for right channel (R). CONNECTION POWER CORO RMD-82 PIN CORD RMX-82/82L RMD 82 RMX-82/82L CAUTION As long as the power cord is plugged into the RMX-82. power is supplied to the unit regardless of the setting of the Standby Button. • A loosened tape may cause trouble in playback or recording. Check the tape before loading it into the deck. If it is slack, insert a pencil or the like into either of cassette's hubs, and rotate it carefully until the slack is taken SWITCHES AND CONTROLS (1) STAND BY Button Depress this button to turn on the unit. The unit is powered through the special cord running from the receiver unit RMX-82. To turn off the unit, press the button a second time. (2) Microphone Jacks When making live recording with stereo microphones, insert the microphone plugs into these jacks. Make sure the right-hand microphone is connected to the right channel jack, and the left-hand microphone to the left channel jack. Be sure to unplug the microphones when recording from other sources. (3) Cassette Controls REC Button To record, press this and PLAY button. The deck is now in the recording mode, and the tape should be winding. The REC indicator glows during recording. REW Button For rapid tape rewind, press this button. PLAY Button Press this button to start the cassette for playback of recorded tape. F.FWD Button Press this button to advance the tape rapidly forward. STOP Button Press this button to stop the tape in any mode: record, playback, rewind, or fast-forward. This button will release any transport mode currently enganged. PAUSE Button Press this button to stop the tape temporarily during recording or playback. When this button is pressed, the PAUSE indicator glows. Pressing the button a second time will restart the tape in the interrupted mode. (4) Tape Selector Used to select the appropriate recording bias and playback equalization, according to type of cassette tape used. Use the METAL button for metal particle tape, the SPECIAL button for chromium dioxide tape, and the NORMAL button for normal tape. See TAPE SELECTOR SETTING GUIDE for details of different brands of cassette tapes and their proper setting positions. (5) Recording Level Control Used to control the recording level of incoming signals, such as from a turntable, tuner, or microphones. This is a dual concentric knob which permits either separate or combined adjustment of both channels. (6) Dolby NR Switch Depress this button to switch in the built-in Dolby NR...