Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
A turned-on TV set in close vicinity may also cause noise. Condensation When the unit is moved from a cold to a warm environment, or when the room temperature rises sharply, condensation forms on parts of the tape transport mechanism, causing malfunctions when the tape deck is operated immediately. To avoid this, allow the tape deck to acclimate to the new temperature by waiting about one hour before operating the unit. PRECAUTIONS CONCERNANT L'INSTALLATION Interférence de bruit Quand l'appareil est placé directement sur l'amplificateur, il peut recueillir un bourdonnement ou autre bruit pendant l'enregistrement. Un téléviseur syntonisé proche peut aussi provoquer du bruit. Condensastion d'humidité Quand l'appareil est déplacé d'un endroit froid à un endroit chaud, ou quand la pièce est chauffée brusquement, de la condensation se forme sur les pièces du mécanisme de transport de bande, ce qui provoque des mauvais fonctionnements quand la platine à cassette est mise en marche immédiatement. Pour éviter ceci, laisser la platine s'acclimater à la température en attendant environ une heure avant de la faire fonctionner. POWER-CORD CAUTION Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest TASCAM authorized service center or your dealer for a replacement. NOTE IMPORTANTE SUR LE CABLE D'ALIMENTATION Tenir le câble d'alimentation par la fiche. Ne pas débrancher la prise en tirant sur le câble et ne pas toucher le câble avec les mains mouillées. Cela risque de provoquer un court-circuit ou un choc électrique. Ne pas poser l'appareil ou un meuble sur le câble. Ne pas pincer le câble. Ne pas faire de noeud avec le câble ou l'attacher à d'autres câbles. Les câbles d'alimentation doivent être posés de façon à ne pas être écrasés. Un câble abîmé peut provoquer un risque d’incendie ou un choc électrique. Vérifier le câble d’alimentation de temps en temps. Contacter le service après-vente TASCAM le plus proche ou le revendeur pour un remplacement AC POWER CORD CONNECTION (FOR CANADA) CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CORDE DE CONNEXION CA ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. 5 En/Fr FEATURES OF DA-20, HIGH PERFORMANCE WITH INTELLIGENCE High-speed search To reduce the searching time in direct tune selection or program play, the HIGH-SPEED search reads the subcodes recorded on tape to learn the tune numbers and tune start positions and searches tunes using these data at a maximum of 300 times the conventional searching speed. Long Play mode Long Play (LP) mode allows to record program sources input in the form of analog signals for twice the period possible in Standard Play mode (up to 4 hours). Even program sources input in the from of digital signals can be recorded in LP mode provided that their sampling frequency is 32 kHz. Subcode application functions Subcodes including various types of time information, start-IDs for indicating the start of tunes, skip-IDs useful for cutting out unwanted sections, tune number data and end mark for indicating the end of programs can be recorded and erased freely. Moreover, you can record TOC (Table Of Contents) data for tape editing and library organization, and HIGH-SPEED search is performed also using this TOC data. Character Pack function This unit incorporates the function for recording and reproducing (displaying) the character data as defined by the DAT format. This function allows an additional recording of a pack of character data in up to 60 characters including the tune name, performer name and memo at the beginning (on the start-ID) of each tune. When this unit reads the character data at the time of playing the tape, it automatically displays the data on the counter display (by scrolling from the right to the left). The read data is stored in the microcomputer so that it can be displayed again by pressing a button. Start-ID recording synchronized with Q codes During recording of digital signal input from a Compact Disc, this unit reads the Q codes recorded on the CD so that start-ID can be recorded precisely even when there is no blank before the tune. As this function is designed to be activated automatically when the microcomputer judges that the program source component is a CD player, no special operation is required to use it. Last Memory Function The condi...