Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
This will prevent damage to the product due to lightning and power-line surges. 16) Power Lines — An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 17) Overloading — Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in risk of fire or electric shock. 18) Object and Liquid Entry — Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 19) Servicing — Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 20) Damage Requiring Service — Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) when the power-supply cord or plug is damaged. b) if liquid has been spilled, or objects have fallen into the product. c) if the product has been exposed to rain or water. d) if the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e) if the product has been dropped or damaged in any way. f ) when the product exhibits a distinct change in performance - this indicates a need for service. 21) Replacement Parts — When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 22) Safety Check — Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 23) Wall or Ceiling Mouting — The product shoud be mounted to a wall or ceiling only as recommended by the manufacturer. 24) Heat — The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. -2 REFERENCE ILLUSTRATIONS Front Panel Display IN NORTH AMERICA USE ONLY ON 120 V SUPPLY. DANS L'AMÉRIQUE DU NORD: UTILISABLE SUR 120 V D'ALIMENTATION UNIQUEMENT. CONNECTIONS (Fig. 1) • Turn off power for all equipment before making connections. • Read instructions of each component you intend to use with the deck. OUTPUT terminals OUTPUT Terminals on the tape deck should be connected to the TAPE PLAY or LINE IN jacks on the amplifier/receiver. LINE IN terminals LINE IN Terminals on the tape deck should be connected to the REC OUT jacks on the amplifier/receiver. Power cord Be sure to connect the power cord to an AC outlet which supplies the correct voltage, as set bythe voltage selector. -3- Stereo Amplifier -4- PRECAUTIONS FEATURES AND CONTROLS (See page 3.) IMPORTANT (for U.K. Customers) Environment Avoid using the deck in the following conditions: • At high temperatures (near a heater, exposed to direct sunlight, etc.). • At extremely low temperatures. • Where there is excessive humidity. • In a dusty atmosphere. • Where power line voltage fluctuations are severe (in which case the use of a voltage regulator may be advisable). Cassette Tape (Fig. 2) Tape Selection: For the automatic tape select function to work properly, metal and chrome (cobalt) tapes must have identification holes. Tape Handling: Do not store tapes in the following places: • On top of heaters, exposed to direct sunlight or in any other places with high temperatures. • Near speakers, on TV sets or amplifiers or where they would be exposed to strong magnetic fields. • Where humidity is high and in dirty, dusty places. • Avoid dropping or subjecting cassettes to excessive shocks. • As C-120 tapes are physically weak and could become entangled in the transport mechanism, do not use them. Voltage Conversion (General export models only) (Fig. 3) Be sure to remove the power cord from the AC outlet before repositioning the voltage converter switch. 1. Locate the voltage selector on the rear panel. 2. Using a flat-bladed screwdriver, set to the appropriate 230 V or 120 V position according to your area. THE APPLIANCE CONFORMS WITH EEC DIRECTIVE 87/308/EEC REGARDING INTERFERENCE SUPPRESSION. * Dolby noise reduction and HX Pro headroom extension manufactured under license from Dolby Laboratorie...