Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
or .) corresponding to the desired direction. After changing the tape transport direction, be sure to press the STOP key (H) to get out of the pause mode. NOTE • Be careful not to press play key whose arrow points in the same direction as the indicator. Doing so will start playback. • Set the REV MODE switch as required. • You don’t need to adjust the recording level or set the Dolby NR system, as both depend on the pre-recorded source tape. 3. Press either DUB START key to start dubbing. For normal speed dubbing, press the NORMAL key. For high-speed dubbing, press the HIGH key. NOTE High-speed dubbing makes a copy at approximately two times the normal speed. We recommend normal speed dubbing for best audio quality. During dubbing, either the NORM DUB or HIGH DUB indicator lights steadily on the display. During normal speed dubbing, only the following keys work: TAPE 1 deck: STOP TAPE 2 deck: PAUSE, REC MUTE, STOP During high-speed dubbing, only the STOP key (H) works. Pressing the STOP key (H) on either deck stops both tapes at once. Neither DUB START key works immediately after the tape is fast-forwarded or rewound to the end. Wait for 5 seconds or more before pressing the key. NOTE • During dubbing, the pitch control does not work. • Recording level adjustment is not necessary for dubbing, as the recording level is set to the level of the pre-recorded tape. Operating the REC LEVEL control, before or after starting dubbing, has no effect at all. • If a nearby television set is switched on during high-speed dubbing, a high-pitched interference noise may be recorded on the tape. To avoid this, either perform dubbing at normal speed, or turn off the television. TASCAM 202MKIV IMPORTANT SAFETY INSTRUCTIONS 4 . Recording Editing during dubbing (only at normal speed) 1. At the desired point during dubbing, press the PAUSE key on the TAPE 2 deck. The TAPE 2 deck only enters the pause mode, allowing you to let unwanted songs go by. To create a 4-second blank between songs, press the REC MUTE key on the TAPE 2 deck. The TAPE 2 deck temporarily stops after recording no signal for 4 seconds. The TAPE 1 deck continues playback when the TAPE 2 deck is in pause mode. You can prevent unwanted songs or unnecessarily 2. To resume dubbing, press the PAUSE key on long blanks from being dubbed, or you can create the TAPE 2 deck. blanks between songs. Synchro reverse dubbing (from TAPE 1 to TAPE 2) When you use this dubbing function and a shorter tape reaches the end of side “A”, it momentarily stops until the other tape reaches the end of side “A”. Then both tapes automatically switch over to side “B” and recording and playback re-start simultaneously. If TAPE 1 is shorter than TAPE 2 When TAPE 1 reaches the end of side “A”, TAPE 1 stops and TAPE 2 enters the “blank recording” mode. When TAPE 2 reaches the end, both TAPE 1 and ll are reversed simultaneously. TAPE l starts reverse play and TAPE 2 resumes recording. When TAPE 1 reaches the end of side “B”, both TAPE 1 and ll stop simultaneously. If TAPE 1 is longer than TAPE 2 When TAPE 2 reaches the end of side “A”, TAPE 1l enters the record-pause mode, while TAPE 1 continues playback. When TAPE 1 reaches the end, TAPE 1 starts reverse play and TAPE 2 starts recording. When TAPE 1l reaches the end of side “B”, both TAPE 1 and ll stop simultaneously. 1. Insert a cassette tape for playback into the TAPE 1 compartment and a cassette tape for recording into the TAPE 2 compartment. Side “A” facing you 2. Set the REV MODE switch to the two-way (E) position. 3. Check the recording direction of both decks. If the reverse direction indicator (.) lights on the display, press the PAUSE key followed by the forward play key (.). Then, be sure to press the STOP key (.) to get out of the pause mode. T TTAS ASASC CCA AAM MM 2 220 002 22M MMK KKI IIV VV IMPORTANT SAFETY PRECAUTIONS 4 . Recording NOTE • Be careful not to press play key whose arrow points in the same direction as the indicator. Doing so will start playback. • You don’t need to adjust the recording level or set the Dolby NR system, as both depend on the pre-recorded source tape. Press the SYNC REV key. 5 The SYNC REV indicator will light on the display. The SYNC REV key does not work if the reverse mode is set to any positions other than E or if the transport direction of both decks is not set to forward (.). Press either DUB START key to start dubbing. For normal speed dubbing, press the NORMAL key. For high-speed dubbing, press the HIGH key. High-speed dubbing makes a copy at approximately two times the normal speed. We recommend normal speed dubbing for best audio quality. During dubbing, either the NORM DUB or HIGH DUB indicator lights steadily on the display. During normal speed dubbing, only the following keys work: TAPE 1 deck: STOP TAPE 2 deck: PAUSE, REC MUTE, STOP During high-speed dubbing, only the STOP key (.) works. Pressing the STOP key (.) on either deck stops both tapes at once. Neither DUB START key works immedi...