Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
The CD The CD Player Enjoying sound effects (LOOP/FLASH) LOOP FLASH You can repeat part of a CD (LOOP) and can “flash” the CD sound (FLASH) during playback. 1 Play a CD. 2 Press and hold LOOP or FLASH at the point you want to start the function. To Press and hold repeat a selected part of a CD LOOP “flash” the CD sound FLASH To cancel the LOOP or FLASH function Release the button. The player returns to normal play. The CD Player The Timer Setting the clock CLOCK TIME SET –, + “--:--” indication appears in the display until you set the clock. Tip The time display system of this player is the 12-hour system: AM12:00 = midnight PM12:00 = noon DISPLAY ENTER Before you set the clock, connect the power source (pages 23 - 25). 1 Press and hold CLOCK for 2 seconds until the hour digits flash. 2 Press TIME SET + or – until you set the current hour. Then press DISPLAY ENTER. The minute digits flash. Set the minutes by pressing TIME SET + or – until the correct minute is displayed. 3 Press DISPLAY ENTER. The clock starts from 00 seconds. The Timer The Timer Waking up to music STANDBY TIMER You can wake up to music or a radio program at a preset time. Make sure you have set the clock (“Setting the clock” on page 19). TIME SET –, + DISPLAY ENTER Before you begin, make sure the t(clock) indication is not lit in the display. If it is lit, press STANDBY. 1 Prepare the music source you want to play. To play Do this a CD Insert a CD. the radio Tune in a station 2 Press TIMER. The t(clock) and the music source (“Cd” or “RAdIO”) flash. 3 Select the music source (“Cd” or “RAdIO”) by pressing TIME SET + or –, then DISPLAY ENTER. 4 Set the timer to the hour you want the music to start by pressing TIME SET + or –, then DISPLAY ENTER. Set the minutes by pressing TIME SET + or –, then DISPLAY ENTER. 5 Set the timer to the hour and the minutes you want the music to go off. (Do as step 4.) The Timer Tips • To exit the standby mode, press STANDBY to make the t indication disappear from the display. • The preset settings remain until you reset them. 6 Set the volume by pressing TIME SET + or –, then DISPLAY ENTER. 7 Press STANDBY. The tindication lights up; the player enters the standby mode. At the preset time, the power will go on, and the music will play. Then the power will go off at the preset time, and the player will enter into the standby mode. To check/change the waking up timer settings Press TIMER , then DISPLAY ENTER. Each time you press DISPLAY ENTER, a stored setting is displayed in the set order. To change the setting, display the setting you want to change and re-enter it. To use the player before a timer playback starts Just turn on the player, and then you can use it. If you turn off the player before the preset time, timer playback will start at the preset time. In case of the radio, however, if you listen to the station which is different from the one you tuned in in step 1 on page 20, you will hear that station at the preset time. Make sure to tune in the station you want to listen to before you turn off the player. To stop play Press POWER to turn off the power. The Timer The Timer Falling asleep to music SLEEP You can set the player to turn off automatically after 10, 20, 30, 60, 90, and 120 minutes, allowing you to fall asleep while listening to music. Tips • When you are playing radio or CD, make sure that (of the tape player is not depressed. • You can fall asleep and wake up to different music. Set the waking up timer first (see page 20), turn on the power, and then set the sleeping timer. However, you cannot store different radio stations. • You can set different volume for the waking up timer and the sleeping timer. For instance, you can sleep at lower volume and wake up at higher volume. Note When you are playing a tape using this function: If the tape length of one side is longer than the set time, the player will not go off until the tape reaches the end. 1 Play the music source you want. 2 Press SLEEP to display “SLEEP”. 3 Press SLEEP to select the minutes until the player goes off automatically. Each time you press the button, the indication changes as follows: “60” n“90” n“120” nno indication n“10” n “20” n“30.” To cancel the sleep function Press POWER to turn off the power. The Timer Setting Up Hooking up the system Make sure you turn off the power before making any connections. Tips • To detach the speakers, unlock speaker (see B on the diagram) and slide the speaker box all the way up and away from the player. • Connect the speakers for this unit only to the speaker terminals of this unit. If you connect any other speakers or equipment, malfunction may occur. Speaker cords 2 Speaker terminals Right speaker 15 Battery compartment Setting UpLeft speaker 3to a wall outlet 1 Inserting the back-up batteries Insert three size AA (R6) batteries (not supplied) into the battery compartment. These batteries work to save the memory data. To remove the batteries, push the ]side. 2 Hooking up the speakers 1 Alig...