Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
As the unit may become hot during operation, always leave sufficient space above the unit for ventilation. If you are mounting the unit in a rack, leave 1U of space above it. Allow at least 10 cm (4 in) at the rear of the unit for ventilation. You should not place the unit on a piece of equipment generating heat, e.g. an amplifier, to avoid possible problems with overheating. Make sure that the unit is mounted in a level position for correct operation. Do not mount the unit in a rack tilted 5° or more from the vertical position. NOTE If the mounting surface is more than 5 degrees away from the horizontal, the tray will not open or close. The voltage supplied to the unit should match the voltage as printed on the rear panel. If you are in any doubt regarding this matter, consult an electrician. NOTE When transporting the unit, always use the original packing materials. For this reason, we strongly recommend that you save all the packing materials that came with the CC-222, in case you need to transport it in the future. In addition, when transporting the unit, you should tape the disc tray closed, using an adhesive tape that will not spoil the finish of the unit. Beware of condensation If the unit (or a compact disc) is moved from a cold making correct operation impossible. To prevent this, to a warm place, or used after a sudden temperature or if this occurs, leave the player for one or two hours change, there is a danger of condensation; vapor in with the power turned on, then turn the power off and the air could condense on the internal mechanism, on again. About tapes Do not store tapes in the following places: • Where humidity is high, or in dirty, dusty places. • Avoid dropping or subjecting cassettes to excessive • On top of heaters, exposed to direct sunlight, or in shocks. any other places with high temperatures. • Near speakers, on TV sets or amplifiers or where As C-120 tapes are mechanically weak, and could they would be exposed to strong magnetic fields. become entangled in the transport mechanism, we do not recommend their use. TASCAM CC-222 Owner’s Manual 7 1 – Introduction—Finalizing For the automatic tape selection function to work Note that Type I (normal), Type II (high-position/ properly, metal and high position (cobalt) tapes must chrome) and Type IV (metal) tapes can be played have the appropriate identification holes. back. Recording is possible with Type I (normal) and Type II (high-position/chrome) tapes. About CD-R and CD-RW discs The CC-222 uses CD-R and CD-RW media, and can also use CD-R and CD-RW Digital Audio media. In this manual, when we refer to “CD-R” and CDRW” discs, we always include “CD-R Digital Audio” and “CD-RW Digital Audio”, even when this is not explicitly stated. CD-R discs can be recorded once only. Once they have been used for recording, they cannot be erased or re-recorded. However, if space is available on the disc, additional material can be recorded. The packaging of CD-R discs will include one of the following logos: By contrast, a CD-RW disc can be used in much the same way as a CD-R disc, but the last track or tracks recorded can be erased before the disc has been “finalized”, and the space on the disc can be re- used for other recordings. The packaging of CD-RW discs will include one of the following logos: However, you should note that an audio CD created using a CD-RW disc may not play back satisfactorily on every audio CD player. It will, naturally, be playable on the CC-222. This is in no way a limitation of the CC-222 itself, but of the difference between the different types of media and the methods used to read them. CD-R discs created on the CC-222, by contrast, may be played satisfactorily on the majority of audio CD players. Finalizing Although audio data may be written on a CD-R or CD-RW disc, a standard CD player will not be able to read the data (i.e. play back the audio) until a final table of contents (TOC) has been written at the start of the disc. The process of writing this table of contents is known as “finalizing”. Once this has been done, no further data can be written to the disk. See “Finalizing” on page 34 for details. In the case of a CD-RW disc which has been finalized, the whole of the disc may be erased, or the disc may be “refreshed”, and the disc re-used. In addition, a CD-RW disc that has been finalized may be “unfinalized”, i.e. the TOC is removed. This allows further tracks to be recorded to the disc, provided that there is space on the disc. “Recordable” discs In this manual, we use the term “recordable” disc to finalized, i.e. further recording is possible on the describe a CD-R or CD-RW disc that has not been disc. 8 TASCAM CC-222 Owner’s Manual 1 – Introduction—Finalizing Handling of compact discs Observe the following: • Always place compact discs in the tray with their label facing upward (compact discs can only be played on one side). • To remove a disc from its storage case, press down on the center of the case, and...