Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Using AC Power The supplied power cord stored inside the battery compartment lets you power the system from a standard AC outlet. 1. While pressing down both tabs on the battery compartment cover in the direction of the arrow, pull the cover down to remove it. 2. Remove the power cord from its storage area in the battery compartment, then replace the cover. 3. Plug the small end of the power cord into the AC jack on the back of the system. Then plug the cord into a standard AC outlet. Cautions: • To prevent electric shock, one blade on the power cord’s plug is wider than the other and the plug fits only one way. If you cannot easily insert the plug, turn it over and try again. Do not force it. 4 • Always plug the power cord into the system before you plug it into a standard AC outlet. Always unplug it from the AC outlet before you unplug it from the system. Installing Batteries You can power the system with six D batteries (not supplied). For the best performance, we recommend alkaline batteries, such as Cat. No. 23-550. Cautions: • Use only fresh batteries of the required size and type. • Never leave dead or weak batteries in the system. • If you do not plan to use the system for several days, or if you plan to power the system using only AC power, remove the batteries. • Dispose of batteries promptly and properly; do not bury or burn them. Follow these steps to install batteries. 1. While pressing down both tabs on the battery compartment cover in the direction of the arrow, pull the cover down to remove it. 14-703.fm Page 5 Wednesday, June 30, 1999 4:56 PM 2. Remove the power cord from its storage area in the battery compartment. 3. Install the batteries as indicated by the polarity symbols (+ and –) marked inside the compartment. 4. Replace the battery compartment cover. If the system’s sound becomes weak or distorted, replace the batteries. USING HEADPHONES To listen to the system without disturbing others, plug a pair of stereo headphones with a 1/8-inch plug (not supplied) into the system’s PHONES jack. This mutes the system’s speakers. Your local RadioShack store sells a wide selection of headphones. Listening Safely To protect your hearing, follow these guidelines when you use headphones. • Set the volume to the lowest setting before you begin listening. After you put on the headphones, adjust the volume to a comfortable level. • Do not listen at extremely high volume levels. Extended high- volume listening can lead to permanent hearing loss. • Once you set the volume, do not increase it. Over time, your ears adapt to the volume level, so a level that does not cause discomfort might still damage your hearing. Traffic Safety Do not wear headphones while operating a motor vehicle or riding a bicycle. This can create a traffic hazard and is illegal in some areas. Even though some headphones are designed to let you hear some outside sounds when listening at normal volume levels, they still present a traffic hazard. 5 14-703.fm Page 6 Wednesday, June 30, 1999 4:56 PM OPERATION PLAYING THE RADIO 1. Set TAPE (POWER OFF)/RADIO to RADIO. 2. Set AM/FM/-STEREO to the desired band and rotate TUNING to tune to the desired station. 3. Adjust VOLUME to a comfortable listening level. 4. Set E-BASS to ON to enhance the bass effect or to OFF for normal bass effect. 5. To turn off the radio, (POWER OFF)/RADIO(POWER OFF). set to TAPE TAPE Notes: • The SCR-63’s AM/FM radio has two antennas. The AM antenna is built-in. For the best AM reception, turn the system. For the best FM reception, fully extend and adjust the telescoping antenna. • If you set AM/FM/-STEREO to -STEREO and a station is received in stereo, the FM STEREO indicator on the front of the system lights steadily. • To improve the reception of a weak FM station, set AM/FM/-STEREO to FM. The signal changes from stereo to monaural, but the reception should improve. 6 LOADING A CASSETTE TAPE Your system has two cassette decks. You can use Deck 1 (PLAYBACK) for normal playback and consecutive play. You can use Deck 2 (RECORD/ PLAYBACK) for normal playback, consecutive play, and dubbing (recording). The control buttons for each deck are located over the deck. Note: Before playing or recording any cassette tape, take up any slack in the tape by turning one of the cassette’s hubs with a pencil. If you do not remove excess slack, the tape might become tangled in the record/playback mechanism. 1. Press STOP/EJECT to open the cassette compartment door. 14-703.fm Page 7 Wednesday, June 30, 1999 4:56 PM 2. Load the cassette tape with its open edge up, the desired side facing out, and the full reel to the right. 3. Gently close the cassette compartment door. PLAYING A CASSETTE TAPE You can play a cassette tape in either Deck 1 or Deck 2, or you can load tapes in both decks and play them consecutively. 1. Load a cassette tape. 2. Set TAPE (POWER OFF)/RADIO to TAPE (POWER OFF). 3. Press PLAY on the deck you are using. The tape plays until it reaches the end of the side, t...