Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
6 Listening to iPod/iPhone 1. Select and place the insert for your iPhone or iPod model. Gently insert an already playing iPhone or iPod. The iP49 will automatically turn on and you will hear the music playing from your iPod/iPhone. Note: If the playing song/music loudness is too low on the iPod itself, the iP49 may not detect that the iPod/iPhone is in play mode. Press the Button to play it. 2. Press the or Button to change iPod/iPhone track forward/reverse. 3. When the iPhone/iPod is docked and in standby mode, press the Button to play it. 4. When the iPhone or iPod is in play mode, press the Button to pause play; press again to resume play. 5. Press the BonGiovi Button to activate the DPS active digital processing circuit. Press again to turn off. 6. Press the Volume or Button to adjust the iP49 volume. 7. Press the eq Button as needed to cycle through treble and bass sound settings. Press the or Button to adjust settings for best sound. 8. To turn off the unit, press the Button. Your iPhone/iPod will continue charging while in the dock if unit is connected to AC power. It will not charge when running on internal battery. Listening to FM Radio Setting up the Antenna Insert the FM Antenna plug into the Aux-in/FM Antenna Jack on the back of the unit. Extend the wire antenna fully for best reception. Do not strip, alter or attach to other antennas. Tuning and Playing the FM Radio 1. Press the Radio/AUX Button as needed to turn iP49 on and toggle between FM radio and aux-in modes. Select FM Radio mode. The last selected radio station will play and the frequency will appear in the display. 2. Press the or Button to tune radio to a desired station. Pressing and holding the or Button (2 sec. then release) will seek the next clear FM radio station. 3. Press the Volume or Button to adjust the volume setting. 4. If needed, move the radio mono/stereo switch located on back of the unit to mono to improve reception/signal. 5. To turn off the unit, press the Button. iPhone/iPod will continue charging while in the dock. Setting and using FM Presets You can set and save up to 6 radio station presets in memory. 1. To set a station as a preset, enter radio mode. Press and hold the preset button. A number will flash indicating the preset number being set and the accompanying frequency. Press the or Button to change the station (hold as above for station seek). Press the preset button to confirm the station as a preset. To review your presets, press and hold the preset button until the display flashes, then press the or Button. Press the preset Button again to exit preset mode. 7 Listening to FM Radio Setting FM Radio Frequency/Range to Use iP49 in Other Countries Different regions of the world use different FM radio frequency steps and ranges. You will need to select the one that matches the standards in your region (USA, EUROPE, JAPAN, AUSTRALIA,or CHINA). The default setting is USA; if you live in the US, you may skip this section. 1. Make sure the iP49 is OFF (not playing in any mode). Press and hold the Radio/AUX Button for about 5 seconds until “USA” flashes in the lower part of the display. Press the or Button to select your region (EU=Europe, JPN= Japan, AUS=Australia, CHN= China). 2. Press the Radio/AUX Button again (or no button within 5 seconds) to exit the radio frequency setting mode. Two beeps will confirm the setting is complete. Using the Aux Line-In Jack with Other Audio Devices The iP49 has an FM antenna/aux line-in jack that lets you play other audio devices through it. Unplug FM antenna to use aux line-in jack. 1. Plug one end of a standard 3.5mm audio patch cord (not included) into the headphone or line-out jack on your audio device and the other end of the patch cord into the iP49 aux line-in Jack, located on the rear of the unit. 2. Press the Radio/AUX Button until “AUX-IN” appears in the display, indicating aux mode is active. 3. Turn on and play your device (device must be controlled independently of the iP49). 4. Press the Volume or Button to adjust the system volume. Adjust the output volume on your device if needed. 5. To turn off the unit, press the Button. Please remember to turn off your device, too. Using the Sleep Timer The iP49 has an adjustable sleep timer that lets you sleep to your iPhone, iPod or FM radio before shutting off after the specified time. 1. Press the sleep button as needed to cycle through the sleep time settings: 90, 60, 30, 15 minutes or OFF (cancels sleep mode). Press the sleep button during sleep operation to review the sleep time remaining. 2. Press the Volume or Button to adjust the sleep volume. This is separate from the unit’s standard volume setting. 3. To turn off the unit, press the Button. Using the Remote auto/on Switch The iP49 has a remote auto/on switch located on the back of the unit. Slide the switch to the AUTO position to save battery power when traveling or operating on the internal battery. AUTO disables remote operation when operating on the internal ...