Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
2. Swing trimmer in and out of the cutting area taking small cuts. F Spool Cap 7 • WARNING Disconnect from the mains electricity supply, before attempting any maintenance or adjustment. Cutting head continues to rotate after the trimmer has been switched off. To remove spool cap 1. Press and hold in the two cap release latches. See fig G. 2. Pull cap away from the cutting head. See fig H. When refitting the spool cap 1. Keep all areas of the cap and spoolholder clean. Failure to do so may prevent the cap being securely located in the spoolholder. 2. Align the two latches on the cap with the two windows in the spoolholder, then press down into the locked position. 3. Ensure the two cap release latches are clearly visible and are fully engaged with the windows in the spoolholder. 4. Check that the cap is correctly fitted by trying to remove it without depressing the two latches. cap release latches G cap spool spoolholder eyelet manual line feed button H USE 8 8 Nylon Line J Do not depress the button more than three times. Excessive line will snag the line cutter and cause the trimmer to malfunction. USE L K hole in spool line eyelet To manually feed the nylon line If required, line can be fed out manually. To operate, gently pull on the line whilst alternately pressing and releasing the button, on the side of the spoolholder. See fig J. To replace nylon line. Replacement nylon line is available from most Electrolux Outdoor Products stockists. You can buy it either as spool and line complete, or as nylon line only. To replace spool and line (complete) 1. Take new spool and remove tape holding line in place. 2. Unwind approximately 100mm of line and feed this through eyelet, see fig K, then drop the spool into spoolholder smooth side uppermost. To replace nylon line on spool. 1. Take line and insert into hole in spool. 2. Turn spool clockwise to wind on required amount of line, (approx. half = 10m) and cut line to length, see fig L. Care should be taken to ensure that the line is neatly coiled on the spool. Failure to do so will impair the efficiency of the automatic line feed. 3. Leave approximately 100mm of line unwound and feed this through eyelet, see fig K, then drop the spool into the spoolholder smooth side uppermost. • Ensure spool is fully located by gently rotating it during fitment. • Remember! Your Flymo Trimmer is designed to use only nylon line with a maximum diameter of 1.5mm. Use only genuine Flymo nylon line. 9 Caring for your Mini-Trim Auto 9 Caring for your Mini-Trim Auto • WARNING Disconnect from the mains electricity supply, before attempting any maintenance or adjustment. Cutting head continues to rotate after the trimmer has been switched off. Keep fingers and hands clear of the line cutter on leading edge of guard. After you have finished using your Flymo Trimmer follow the procedure below: 1. Disconnect from the mains electricity supply 2. Never clean your trimmer with water, cleaning fluids, or solvents, just remove debris with a suitable tool, a soft brush or dry cloth. 3. Using the scraper provided, clean around the inside of the cutting head housing to remove any grass and debris. (Fig M) 4. Using a soft brush, clean around the inside of the cutting head housing (Fig N), the cutting head (Fig P) and the motor housing air vents.(Fig Q) 5. Inspect the trimmer carefully, especially the parts of the cutting head. 6. If your trimmer is damaged in any way contact your local Electrolux Outdoor Products approved service centre. • Never use a damaged trimmer. 7. Wind cable carefully to avoid kinking. 8. Store in a cool, dry place and out of reach of children. M N P Q MAINTENANCE 10 10 Fault Finding Hints & Service Recommendations MAINTENANCE Fault Finding Hints Service Recommendations 1. Line too short Manually feed out the line. 2. Line broken inside cutting head. Remove cap and re-thread line. 3. Line jammed on spool Remove cap and spool and rewind line to remove crossed loops. 4. Poor performance Ensure inside of cutting head housing is clean and free from debris. 5. Trimmer stops during use. Release switch lever and wait 30 seconds before re-starting. 1. We strongly recommend that your product is serviced at least every twelve months, more often in a professional application. 2. Always use genuine Flymo Spare Parts. 3. Prepacked spares are available from most Electrolux Outdoor Products stockists. 4. If you have a problem with your machine contact your local Approved Service Centre ensuring you have full details of your product as described on the product rating label. 5. Should it be necessary for work to be carried out by your Service Centre, it is important to take your complete machine with you. 6. In the event of further difficulty please contact:- Electrolux Outdoor Products Customer Service Preston Road Aycliffe Industrial Estate NEWTON AYCLIFFE Co. Durham DL5 6UP Telephone: (01325) 300303 Fax : (01325) 318193 A network of specialist dealers can be found in your local Yellow Page...