Iniciar sesión:
Votos - 2, Puntuación media: 4.5 ( )

Manual de usuario Canon, modelo Trimmer

Fabricar: Canon
Tamaño del archivo: 2.4 mb
Nombre del archivo: digital_press_Two_Knife_Booklet_Trimmer_A1.pdf
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


2-2 Operation While Trimming...................................................................................................2-3 Section 3 Troubleshooting Error Messages ...................................................................................................................3-2 Service Call Error ...........................................................................................................3-2 Error Message Chart ......................................................................................................3-3 Clearing Paper Jams ...........................................................................................................3-4 Section 4 Appendix Specifications ......................................................................................................................4-2 Specifications .................................................................................................................4-2 Index .................................................................................................................................... 4-3 iv Before You Begin CHAPTER Machine Descriptions...........................................................................................................................1-2 Section Descriptions............................................................................................................................1-3 [1] Two-Knife Trim Section..............................................................................................................1-3 [2] Conveyor Section.......................................................................................................................1-4 [3] Trim Ejecting Section.................................................................................................................1-5 1-1 Machine Descriptions [1 ] Two-Knife Trim Section (See page 1 -3.) [2] Conveyor Section (See page 1-4.) [3] Trim Ejecting Section (See page 1-5.) 1-2 Machine Descriptions [1] Two-Knife Trim Section Each booklet delivered from the upstream trimmer is trimmed along its top and bottom, and then delivered to the conveyor section. Handle L Booklet Transport Unit [TF2] If any booklets jam in the two-knife trim section, press the handle and lift up this mechanism to remove the jammed booklets. Opening the Transport Unit 1. Press the handle to the left. 2. Lift the mechanism up. Trim Knives These knives trim top and bottom of each booklet. Section Descriptions 1-3 [2] Conveyor Section Booklets delivered are laid out on the conveyor. Handle [TE] Grip this handle and lift the roller unit when removing booklets on the conveyor. Delivery Tray *1 This tray holds stacked booklets. It is removable. (When the tray is removed, the conveyor full condition not detected, and continuous operation is possible.) *1 Removing the delivery tray. 1. Loosen two locking knobs. 2. Lift the delivery tray up to remove. 3. Tighten two locking knobs. Delivery Transport Rollers Output booklets are held by these rollers. The position of the rollers is set automatically to match booklet sizes. Booklet Detect Sensor This sensor detects when the conveyor is full of stacked booklets. Transport Belts These belts move booklets after they are ejected. 1 -4 Section Descriptions [3] Trim Ejecting Section Trim is ejected into the trim box through this section. Trim Full Sensor If trim stacks up between the sensor and the reflector, the Trim Full error is indicated. Delivery Chute Trim is ejected into the trim box through this chute. \ Trim Box Section Descriptions 1-5 1 -6 Section Descriptions Operating Procedures CHAPTER Trimmer Setup.....................................................................................................................................2-2 Operation While Trimming...................................................................................................................2-3 2-1 Trimmer Setup Turn on the power switch on the saddle stitcher first, then turn on the power switch on the host machine (printer). The trimmer will also be powered on as it is connected to the saddle stitcher. See the operation manual for the printer and set up the printer. 2-2 Trimmer Setup Operation While Trimming • When the conveyor is full of booklets, remove the booklets. If the machine stops because the conveyor is full, remove the booklets, and operation restarts automatically. $1 Note • If you remove booklets before the conveyor is full, you can increase production efficiency without interrupting operation. • Be careful not to drop a booklet while removing it. • When the trim box is full, empty it. à If the machine stops because the trim box is full, and trim stacks up between the sensor and the reflector, remove trim, and operation will restart automatically. Note • If you remove trim before the trim box is full, you can increase...


Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría