Votos - 2, Puntuación media: 3.5
(
)
)
|
Fotos y especificaciones Viconte VC-1462 |
Resumen del manual
With the hair dry, it is much easier to control the length of hair being cut. • Cutting hair requires practice so it is always better to leave the hair longer for the first few haircuts until you become used to the length to which each comb attachment cuts the hair. ATTACHMENT COMB • Attachment comb № 1 leaves 3 mm (1/8 inch) hair length. • Attachment comb № 2 leaves 6 mm (1/4 inch) hair length. • Attachment comb № 3 leaves 9 mm (3/8 inch) hair length. • Attachment comb № 4 leaves 12 mm (1/2 inch) hair length. • Each comb attachment is marked accordingly on its outside middle surface. • To attach a comb, hold it with its teeth upward and slide it onto and along the clipper blade until the front of the comb firmly seats against the clipper blade. • When you use the clipper for the first time, cut only small portions of hair until you are accustomed to the cutting length with a certain comb attachment. • For even cutting, allow the comb attachment/cutter to cut its way through the hair. Do not force it through quickly. Also remember to comb the hair frequently to remove trimmed hair and check for uneven strands. STEP 1 - NAPE OF THE NECK • Attach comb attachment 3mm or 6mm. • Hold the clipper cutting edge pointed up and begin the haircut, starting at the centre of the head at the base of the neck (fig.1). • Hold the clipper comfortably in your hand and hold lightly against the head with the comb teeth pointing upward Gradually and slowly lift the clipper, working upwards and outwards, through the hair, trimming just a little at a time. • As you cut, gradually lift the hair clipper head towards you. Continue to cut the back area from the bottom of the neck upwards to the top of the ears. STEP 2 - BACK OF THE HEAD » Change to the next longest comb attachment 9mm or 12mm and cut the back of the head (fig.2). STEP 3 - SIDE OF THE HEAD » Change to one of the shorter combs 3mm or 6mm, trim sideburns, i.e. the hair directly in front of the ears. Then change to one of the longer combs, 9mm or 12mm, and continue to cut to the top of the head (fig.3). STEP 4 - SIDE OF THE HEAD • Using comb attachment 9mm or 12mm, cut top of head from back to front against the direction in which the hair normally grows (fig.4). In same cases, this may require the reverse, or cutting from front to back. • Comb attachment 3mm or 6mm are used to achieve a close crew cut or short cut. • For longer hair on top, use the comb provided and lift hair on the top of the head. Cut over the comb, with the hair lifted or hold the hair between the fingers to lift it and cut it to desired length (fig.5,6). Always work from the back of the head. You can cut the hair shorter gradually by reducing the space between the comb/fingers, and the head. Comb out trimmed hair and check for uneven strands. STEP 5 - THE FINISHING TOUCH » Finally, use the taper level without an attachment comb for close trimming around the base of the neck, the sides of the neck and the ears. » To produce a clean straight line at the sideburns, reverse the hair clipper by turning the reverse side uppermost (fig.7). » Press the clipper at right angles to the head, tips of the blades lightly touching the skin and work downwards. This way you obtain, as a clean cut as would be given by a razor. SHORT TAPERED STYLES - "FLAT TOP" AND SHART CUTS » Starting with the longest attachment comb (12mm), cut from the back of the neck to the crown. Hold the attachment comb flat against the head and slowly move the clipper through the hair, as shown (fig.8). » Cut the hair against the direction in which it grows from the front to the crown and then level the cut with the sides. » To give a "flat top" look, the hair on top of the head must be cut over the top of a flat comb rather than by using the attachment comb. Use closer cutting attachment combs to taper the hair down to the neckline as desired. Comb hair and check for uneven areas and outlining sideboards and neckline as described previously. CLEANING AND STORAGE • Remove cut hair from the clipper with the brush enclosed. • Wipe the cutter with a dry soft cloth. • Oil the blades as mentioned above. • Keep the appliance in a dry room. • You may hang the cutter by provided loop. • The blades must be oiled for storage period. SPECIFICATION Power supply 230 V, 50 Hz Power 15 W Net/ Gross Weight 0.372 kg / 0.500 kg Gift box dimension (L x W x H) 180 mm x 58 mm x 240 mm 9 мм 12 мм 10 11 12 1. Защитная крышка для режущих лезвий 2. Лезвия 3. Регулятор длины срезаемых волос 4. Корпус 5. Переключатель Вкл./Выкл. 6. Защита шнура от перекручивания 7. Петелька для подвешивания 8. 4 съемных гребня 9. Расческа 10. Ножницы 11. Масло 12. Щеточка для чистки лезвий 13. Фикстаор филировочного гребня 9 МЕРЫ БЕЗОПАСНОСТИ При обращении с прибором, особенно в присутствии детей, следует соблюдать следующие меры предосторожности: • Использовать только в бытовых целях. Прибор не предназначен для промышленн...