Votos - 3, Puntuación media: 4 ( )

Fabricar: Homelite Tamaño del archivo: 3.45 mb Nombre del archivo: Idioma del manual:

String advances each time the head is tapped. . Several taps may be required until string strikes the cut off blade. . Resume trimming. NOTE: If the string is worn too short you may not be able to advance the string by tapping it on the ground. If so, STOP THE ENGINE, and manually advance the string. ADVANCING THE STRING MANUALLY With the engine off, push the spool retainer down while pulling on string(s) to manually advance the string. CUT-OFF BLADE This trimmer is equipped with a cut-off blade on the grass deflector. For best cutting, advance string by tapping the string head until the string is trimmed to length by the cut-off blade. Advance string whenever you hear the engine running faster than normal, or when trimming efficiency diminishes. This will maintain best performance and keep string long enough to advance properly. DANGEROUS CUTTING AREA BEST CUTTING AREA BEST CUTTING AREA DANGEROUS CUTTING AREA mightylite 26ss direction of rotation mightylite 26cs Fig. 10 direction of rotation Page 13 Fig. 11 Spool Retainer MAINTENANCE WARNING: When servicing, use only identical Homelite replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during tool operation. If operation is dusty, also wear a dust mask. WARNING: Before inspecting, cleaning, or servicing the machine, shut off engine, wait for all moving parts to stop, and disconnect spark plug wire and move it away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. GENERAL MAINTENANCE Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, lubricant, grease, etc. WARNING: Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating lubricants, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury. You can often make adjustments and repairs described here. For other repairs, have the trimmer serviced by an authorized service dealer. SPOOL REPLACEMENT EZ wind™ Tap Advance System New prewound spool See Figures 11 - 12. If replacing string only, refer to String Replacement later in this manual. Use only .080 in. diameter trimmer line. Use original manufacturer’s replacement string for best performance. . Stop the engine and disconnect the spark plug wire. Hold the string head and unscrew the spool retainer. To remove the spool retainer: Turn the spool retainer counterclockwise for MightyLite 26CS. Turn the spool retainer clockwise for MightyLite 26SS. . Remove the empty spool from the string head. Keep the spring attached to the spool. . For the MightyLite 26CS: Make sure the string is captured in the slot on the new spool. Make sure the end of the string is extended approximately 6 in. beyond the slot. For the MightyLite 26SS: Make sure the two strings are captured in the slots opposite each other on the new spool. Make sure the end of each string is extended approximately 6 in. beyond each slot. . Align the slot(s) on the spool to the eyelet(s) on the string head housing. Push down and turn the spool in the necessary direction to align the slot(s). . Make sure the string head and the spool retainer are installed on the drive shaft. To install the spool retainer: Turn the spool retainer clockwise for MightyLite 26CS. Turn the spool retainer counterclockwise for MightyLite 26SS. . For the MightyLite 26CS: Slide the string into the housing eyelet and pull outward to rotate the spool into the cutting position. For the MightyLite 26SS: Slide strings into the housing eyelets and pull outward to rotate the spool into the cutting position. . Push the spool retainer down while pulling on string(s) to manually advance the string and to check for proper assembly of the string head. Fig. 12 INSERT INTO STRING HEAD PUSH DOWN AND TWIST TO ALIGN Page 14 MAINTENANCE STRING REPLACEMENT See Figures 13 - 16. . Stop the engine and disconnect the spark plug wire. Hold the string head and unscrew the spool retainer. To remove the spool retainer: Turn the spool retainer counterclockwise for MightyLite 26CS. Turn the spool retainer clockwise for MightyLite 26SS. . Remove the spool from the string head. NOTE: Keep the spring attached to the spool. Remove any old string remaining on the spool. .n For the MightyLite 26CS: Cut one piece of trimmer line 9 ft. long. Find the hole in the center of the spool (figure 14). Insert one end of the line into the hole. Carefully wind the string in the direction indicated on the top of the spool. Nearing the end of the string, slide the end of the string into the nearest open slot on the spool. Do not overfill. For the MightyLite 26SS: Cut one piece of trimmer line 18 ft. long. Find the middle of the string section. Loop the string arou...

Descargar ahora

Introduzca dos números de la imagen: