Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added. IMPORTANT Stored two-stroke fuel may separate. ALWAYS shake fuel container thoroughly before each use. 3 m (10 ft.) SM T W T F S 1 2 3 4 5 6 7 8 9 1011 1213 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 HEDGE CLIPPER OPERATOR'S MANUAL 15 EQUIPMENT CHECK Before operation a complete check of the unit must be performed; • Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed. • Inspect fuel lines, tank and area around carburetor for fuel leaks. DO NOT operate unit if leaks are found. • Never adjust blades when the engine is operating. • Inspect hand guard for damage. Replace if damaged or missing. • Check that the blade assembly is firmly attached and in safe operating condition. Dull, loose or damaged blades should not be used. DETERMINE OPERATION AREA • Before starting the unit, equip yourself and fellow workers in the 4.5 m (15 ft.) safety zone with the required protective equipment and clothing. • Review the area to be trimmed. Look for hazards that could contribute to unsafe conditions. • Spectators, children and animals must be prevented from coming nearer than 4.5 m (15 Ft.) while the Hedge Clipper is in use. 4.5 m (15 ft.) 16 16 OPERATION • Provide all users of this equipment with the Operator's Manual and instructions for Safe Operation. • Before starting the unit, equip yourself and any other person working within the 4.5 m (15 ft.) Safety Zone with the required Protective Equipment and clothing. • During operation, the complete unit, especially the gear box may become very hot, too hot to touch. Avoid contact during and immediately after operation. • Do not operate this product indoors or in inadequately ventilated areas. 4.5 m (15 ft.) STARTING COLD ENGINE 1. STOP SWITCH - START/RUN. Move stop switch (A) away from the STOP position. 2. CHOKE - COLD START. Move choke (B) to the Cold Start (CLOSED) position. 3. PRIMER - PUMP BULB. Pump primer bulb (C) until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times. C B COLD START RUN IDLE H L A A HEDGE CLIPPER OPERATOR'S MANUAL 17 4. START - PULL ROPE Lay the hedge clipper on a flat clear area and pull the recoil starter handle (D) until engine fires. 5. OPEN CHOKE - RUN. Move choke (B) to the RUN (OPEN) position. Restart engine if necessary and allow unit to warm up at idle for several minutes. WARNING DANGER The blades should not move at idle. If blades move, readjust carburetor according to "Carburetor Adjustment" instructions in this manual or see your ECHO Dealer, otherwise serious personal injury may result. 6. After engine warm up, gradually depress throttle trigger to increase engine RPM to operating speed. BCOLD START RUN IDLE H L STARTING WARM ENGINE The starting procedure is the same as Cold Start except DO NOT close the choke. WARNING DANGER The blades should not move at idle. If blades move, readjust carburetor according to "Carburetor Adjustment" instructions in this manual or see your ECHO Dealer, otherwise serious personal injury may result. 1. STOP SWITCH - START/RUN Move stop switch (A) away from the STOP position. 2. START - Pull Rope Lay the hedge clipper on a flat clear area and pull the recoil starter handle (D) until the engine fires. NOTE If engine does not start after 5 pulls, use Cold Start Procedure. 18 18 STOPPING ENGINE 1. RELEASE THROTTLE. Allow engine to idle for a minute. 2. STOP SWITCH - STOP. Move stop switch (A) to STOP position. WARNING DANGER If engine does not stop when stop switch is moved to STOP position, close choke - COLD START position - to stall engine. Have your ECHO dealer repair stop switch before using hedge clipper again. MAINTENANCE Your ECHO Hedge Clipper is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your Hedge Clipper achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed, see your ECHO Service Dealer for repairs. SKILL LEVEL Level 1= Easy to do. Most required tools come with unit. Level 2= Moderate difficulty. Some specialized tools may be required. Level 3= Experience required. Specialized tools are required. ECHO recommends the unit be returned to your ECHO dealer for servicing. ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier. Just below each task heading are listed the various part numbers required for that task. See your ECHO dealer for these parts. HEDGE CLIPPER OPERATOR'S MANUAL 19 MAINTENANCE INTERVALS Component/System Maintenance Procedure Before Use Every Refuel Daily or Every 4 Hours 3 Months or 100 Hours 6 Months or 300 Hours Yearly or 600 Hours Air Fi...
Otros modelos de este manual:Clippers - 2410 - Type 1E (902.37 kb)
Clippers - 2410 - Type 2E (902.37 kb)
Clippers - HC-1500 (902.37 kb)
Clippers - HC-1500 - Type 2E (902.37 kb)