Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
. Check if the voltage indicated on the appliance corresponds to the local mains voltage before you connect the appliance. . If the cord or adapter is damaged, it must be replaced by Philips, a service centre authorised by Philips or similarly qualified persons in order to avoid a hazard. . The adapter contains a transformer. Do not cut off the adapter to replace it with another plug, as this will cause a hazardous situation. . The adapter transforms 220-240 volts to a safe voltage lower than 24 volts. . Keep the appliance and the adapter dry. . Keep the appliance out of the reach of children. . Store and use the appliance at a temperature between 5cC and 35cC. . Do not use the appliance if the cutting unit or comb attachment is damaged or broken, as this may cause injury. . This appliance is only intended for clipping human scalp hair. Do not use it for any other purpose. . Noise level: Lc = 69 dB [A] Preparing for use Clipping with comb attachment: 1 Slide the arms of the comb attachment into the guiding grooves of the appliance (fig. 1). 2 Press the adjustment button on the back of the appliance and slide the comb attachment to the desired position (see table) (fig. 2). 3 Release the adjustment button to lock the comb. 4 Insert the mains plug into the wall socket. 5 Switch the appliance on. 4203 000 54971 09-02-2006 07:20 Pagina 7 ENGLISH 7 If a lot of hair has accumulated in the comb attachment, remove it and blow and/or shake the hair out of it. Hair length settings setting resulting hair length 1 4 mm 2 7 mm 3 10 mm 4 13 mm 5 15 mm 6 18 mm 7 21 mm Clipping without comb attachment 1 To remove the comb attachment, press the adjustment button on the back of the appliance and slide the comb attachment to its final position (fig. 3). 2 Pull the comb attachment off the appliance with your other hand while keeping the button pressed (fig. 4). Clean the appliance ever y time you have used it. Clipping techniques Always comb the hair in the direction of growth before clipping. Clipping with comb attachment The comb attachment can be used to obtain hair lengths up to 21mm. . Start clipping at the setting for maximum hair length (i.e. position 7) to familiarise yourself with the clipper. Always move the clipper against the direction of hair growth. . Hold the clipper so that the flat side of the comb attachment is parallel to the head. Move it slowly through the hair and then away from the head, cutting only a small amount at a time (fig. 5). 4203 000 54971 09-02-2006 07:20 Pagina 8 8 ENGLISH . Change the hair length setting (see table) to obtain different lengths on different parts of the head. Cutting over styling comb or fingers This technique can be used to obtain hair lengths over 21mm. . Remove the comb attachment. . Lift a small section of hair with a styling comb or grasp it between two fingers (fig. 6). . Lift the hair with the comb or fingers so that only the length that needs to be cut off sticks out (fig. 7). . Trim the hair protruding from the comb or fingers. . Continue this procedure working against the direction of hair growth. . Comb frequently to remove cut hair and to check for unevenly cut sections. Outlining . Remove the comb attachment. . Hold the clipper with the cutter pointing downwards (fig. 8). . Make overlapping strokes for precise outlining of the neck and sideburns (fig. 9). . To cut the hair around the ears, put one edge of the cutting unit on the skin. Make sure that the teeth are kept at a safe distance from the ears (fig. 10). . Shape the desired outline slowly and carefully (fig. 11). Creating different haircuts Crew cut . Select the desired hair length setting for the neck area (fig. 12). . Clip the neck area using the 'Clipping with comb attachment' technique (fig. 13). . Adjust the setting to the desired hair length for the back and sides of the head. . Clip the sides and back of the head, leaving the hair on top of the head uncut (fig. 14). 4203 000 54971 09-02-2006 07:20 Pagina 9 ENGLISH 9 . For a flat top look, cut the hair on top of the head using the 'Cutting over styling comb or fingers' technique (fig. 15). . Finish the haircut by clipping the neckline, sideburns and the area around the ears using the 'Outlining' technique. Short cut . Select the desired hair length setting for the back and the sides of the head (fig. 16). . Clip the back and the sides of the head using the 'Clipping with comb attachment' technique (fig. 17). . Leave the hair on top of the head uncut. . Select the desired hair length setting for the top of the head. . Clip the top of the head using the 'Clipping with comb attachment' technique (fig. 18). . Finish the haircut by clipping the neck, sideburns and area around the ears using the 'Outlining' technique. Cleaning Do not use abrasive cleaning agents, scourers or liquids such as alcohol, petrol or acetone to clean the appliance. 1 Make sure the appliance is switched off and disconnected from the mains before you start cleaning it. 2 Remove the ...