Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
B For a single trimming session the appliance must be charged for at least 90 minutes. Optimising the lifetime of the rechargeable battery -After the appliance has been charged for the first time, use it until the batter y is completely empty. - Do not charge the appliance for more than 24 hours. ENGLISH -Do not keep the powerplug plugged into the wall socket all the time. - Do not recharge the appliance between the trimming sessions. -Discharge the batter y completely twice a year by letting the motor run until it stops. Then fully recharge the batter y. -If the appliance has not been used for a long period of time, it must be fully recharged. Preparing for use Always comb your beard or moustache with a fine comb before you star t trimming. Using the appliance Absorbing cut hairs The suction system is activated automatically as soon as you switch the appliance on. It absorbs cut hairs during ever y kind of use, i.e. trimming with and without comb attachment and contouring.The flexible hair guide follows the contours of the face and directs cut hairs towards the nozzle of the vacuum mechanism. We advise you to empty the hair-collection chamber after each trimming session. When trimming long, dense beards it may also be necessar y to empty the hair-collection chamber during the trimming session in order to maintain optimal suction performance (also see chapter 'Cleaning', section 'Hair-collection chamber'). B To ensure optimal functioning of the vacuum system, do not cut off more than approx. 7mm of your overall beard length at a time. If you want to cut your beard shorter, repeat the process one or more times. Trimming with comb attachment 1 Turn the adjustment ring (Precision Zoom Lock`) to the desired trimming length setting (see table) (fig. 3). . The setting will appear in the window below the adjustment ring (Precision Zoom Lock`). ENGLISH If you are trimming for the first time, start with the maximum trimming length setting (9). 2 To trim in the most effective way, move the trimmer against the direction of hair growth. Do not move the trimmer too fast. Make smooth and gentle movements and make sure the surface of the comb always stays in contact with the skin (fig. 4). Trimming length settings Resulting hair lengthSetting 1.5 mm 2.5 mm 4 mm 5.5 mm 7.5 mm 9.5 mm 12 mm 15 mm 18 mm Trimming at the unique 'stubble look' setting . Use the trimmer with the comb attachment set to length setting 1.This allows you to create a 'stubble look' (fig. 5). Trimming without comb attachment Full beards and single hairs. 1 Remove the comb attachment (fig. 6). B Never pull at the flexible top of the comb attachment. Always pull at the bottom part. 2 Make well-controlled movements and touch the hair lightly with the trimmer (fig. 7). 10 ENGLISH Cleaning The appliance may only be cleaned dry. Do not use abrasives, scourers or liquids such as alcohol, petrol or acetone to clean the appliance. Never use sharp or hard objects to clean the filter to avoid damaging it. Hair-collection chamber 1 Switch the appliance off. 2 Remove the hair-collection chamber and remove the hairs by shaking or brushing them out (fig. 8). 3 For extra thorough cleaning and to maintain optimal suction performance, detach the filter.. (fig. 9). 4 ...and carefully clean the hair-collection chamber and the filter with the brush supplied (fig. 10). Appliance 1 Remove the comb attachment. 2 Remove the cutting unit (fig. 11). 3 Clean the cutting unit and the inside of the appliance with the brush supplied (fig. 12). 4 Reattach the cutting unit and the comb attachment to the appliance (fig. 13). Replacement Worn or damaged cutting units and filters should only be replaced with original Philishave replacement par ts which are available at your dealer or at authorised Philips ser vice centres. ENGLISH 11 Environment The built-in rechargeable batter y contains substances that may harm the environment. Do not throw the batter y away with the normal household waste but hand it in at an official collection point. You can also take the appliance to a Philips ser vice centre, where staff will be happy to help you remove the batter y and dispose of it in an environmentally safe way. Removing the battery Follow the steps below to remove the batter y. 1 Disconnect the appliance from the mains and let the appliance run until the motor stops. 2 Separate the two housing parts by means of a screwdriver (fig. 14). 3 Pull out the printed circuit board (fig. 15). 4 Remove the rechargeable battery by means of a screwdriver and detach it by bending or turning it several times until the connections break (fig. 16). 5 Dispose of the battery and the other components in an environmentally safe way. Do not connect the appliance to the mains again after it has been opened. Guarantee & service If you need information or if you have a problem, please visit the Philips Web site at or contact the Philips Customer Care Centre in your countr y (you will find its phone num...