Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
770-5200D NDEX Safe Operation Practices.....................3 Assembly Instructions.................... . . 4 Operation ............................... 7 Adjustments............................. 7 Lubrication.............................. 8 Maintenance ............................ 8 Off-Season Storage........................ 9 Trou be Shooting Chart.................... 9 Illustrated Parts..........................10 Replacement Parts List....................11 A Instructions given with this symbol are for personal safety. Be sure to follow them. àic WARNING I This unit is equipped with an internal combust forest-covered, brush-covered or grass-coverec spark arrester meeting applicable local or state in effective working order by the operator. on engine and should not be used on or near any unimproved land unless the engine's exhaust system is equipped with a aws (if any). If a spark arrester is used, it should be maintained In the State of California the above is required fcy law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal lav/s apply on federal lands. A spark arrester muffler is available through your nearest engine authorized service center. | WARNING | *o reduce the potential for any injury, comply with the following safety instructions. Failure to comply with the structions may result in personal injury. SAFE OPERATION PRACTICES FOR EDGERS TRAINING 1. Read this owner's manual carefully in its entirety before attempting to assemble or operate this machine. Be completely familiar with the controls and the proper use of this machine before operating it. Keep this manual in a safe place for future and regular reference and for ordering replacement parts. 2. Your edger is a precision piece of power equipment, not a plaything. Therefore, exercise extreme caution at all times. 3. Never allow children to operate a power edger. Only persons well acquainted with these rules of safe operation should be allowed to use your -edger. 4. Keep the area of operation clear of all persons, particularly small children and pets. Stop engine when they are in the vicinity of your edger. Although the area of operation should be completely cleared of foreign objects, an object may have been overlooked and could be accidently thrown by the edger in any direction and cause serious personal injury to the operator or any others allowed in the area. 5. No one should operate this unit while intoxicated or while taking medication that impairs the senses or reactions. PREPARATION 1. Thoroughly inspect the area where the equipment is to be used. Remove all stones, sticks, wire, bones and other foreign objects which could Be picked up and thrown by the edger in any direction and cause serious personal injury to the operator or any others allowed in the area. 2. Do not operate equipment when barefoot or wearing open sandals. Always wear substantial footwear. 3. Checkthefuel before starting the engine. Gasoline is an extremely flammable fuel. Do not fill the gasoline tank indoors, while the engine is running, or while the engine is still hot. Wipe off any spilled gasoline before starting the engine as it may cause a fire or explosion. 4. Disengage the blade clutch on units so equipped ^ before starting the engine. Never attempt to make a wheel adjustment while the engine is running. 6. Never operate the equipment in wet grass. Always be sure of your footing. A slip and fall can cause serious personal injury. Keep a firm hold on the handle and walk, never run. OPERATION 1. Never operate this edger unless wearing safety glasses or some other suitable eye protection at all times the engine is running. 2. Do not change the engine governor settings or overspeed the engine. 3. Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at ai! times as the rotating blade can cause injury. 4. Stop the blade when crossing gravel drives, walks or roads. 5. After striking a foreign object, stop the engine, remove the wire from the spark plug, and thoroughly inspect the edger for any damage. Repair the damage before restarting and operating the edger. 6. If the equipment should start to vibrate abnormally, stop the engine and check immediately for the cause. Vibration is generally a warning of trouble. 7. Stop the engine whenever you leave the equipment, before cleaning the guard assembly, and when making any repairs or inspections. 8. Before cleaning, repairing or inspecting, make certain the blade and all moving parts have stopped. Disconnect the spark plug wire, and keep the wire away from the spark plug to prevent accidental starting. 9. Do not run the engine indoors. 10. Shut the engine off and wait until the blade comes to a complete stop before unclogging guard assembly. 11. Never operate edger without proper guards, plates or other safety protective devices in place. 12. Always operate the edger so that the protec...
Otros modelos de este manual:Clippers - 249-569-000 (1.08 mb)
Clippers - 249-596-000 (1.08 mb)