You can adjust the sound with the VOLUME control. This adjustment does not affect the content of recording. RECORDING WITH BUILT-IN MICROPHONE • Slide the Function switch to TAPE position. • Insert a blank cassette into deck. • Press the PLAY button and RECORD button simultaneously to start recording. • Press the STOP/EJECT button when finished. NOTE: Monitoring during MICROPHONE recording is not possible. 5 MAINTENENCE AND CARE • Check your batteries regularly, old or discharged batte

CD SKIP/SEARCH button 14. PROGRAM button 15. REPEAT button 16. Left speaker 17. UBBS button 18. VOLUME control regulator 19. Stereo headphone jack 20. FUNCTION switch 21. CD door 22. PAUSE button 23. STOP/EJECT button 24. FAST FORWARD button 25. REWIND button 26. PLAY button 27. RECORD button Important safeguards • ATTENTION: The owner’s manual contains important operating and maintenance instructions. For your safety, it is necessary to refer to the manual. • DANGEROUS VOLTAGE:

Always press "STOP" button to stop the disc spinning first. • Place a CD into the compartment with the label-side (printed side of disc) facing upwards. Press down in the center part of disc until the disc "locks" onto the center spindle. • When the CD has been placed onto the center spindle, gently lower the CD-door downwards until it locks shut. • The CD is now ready to be played. • To remove a disc, follow the same procedure as described above, except to remove the CD instead of inserting

Connect the Power Adapter cord plug to the clipper and switch ON. If the clipper does not start immediately when plugged in, switch it OFF. Wait approximately 1 minute. Switch back ON and begin trimming. Guide comb attachment The Guide Comb helps to guide hair to cutting blades and gives you precise control of hair lengths. It may be removed if you are: • Defining/outlining hairline edges • Trimming nape of neck • Trimming with a Barber's comb or fingers To Remove the Guide Comb: 1. Be ce

CD SKIP/SEARCH button 14. CD SKIP/SEARCH button 15. PROGRAM button 16. Left speaker 17. DBBS button 18. VOLUME control regulator 19. Stereo headphone jack 20. FUNCTION switch 21. CD door 22. PAUSE button 23. STOP/EJECT button 24. FAST FORWARD button 25. REWIND button 26. PLAY button 27. RECORD button Important safeguards • ATTENTION: The owner’s manual contains important operating and maintenance instructions. For your safety, it is necessary to refer to the manual. • DANGEROUS

Vt-13 53.qxd 07.02.03 11:16 Page 2 МАШИНКА ДЛЯ СТРИЖКИ ВОЛОС HAIRCUTTING SET Модель VT-1353 ИНСТРУКЦИЯ ПО ПРИМЕНЕНИЮ MANUAL INSTRUCTION Vt-13 53.qxd 07.02.03 11:16 Page 4 ENGLISH Blade level On/off switch Bottom blade Top blade Power screw PART NAME 9 mm 12 mm Comb Scissors Oil Brush 2 Гарантийный талон Сведения о покупке Модель: Серийный N2: МН 135300000 Дата покупки: Сведения о продавце Название и адрес продающей организации ТелефонД Подтверждаю получение исправного изд

Для подравнивания волос вокруг шеи и около висков установите регулятор длины срезаемых волос в нижнее положение. Переверните машинку обратной стороной и подравняйте волосы на висках и шее. Для конечной обработки надавите правым углом машинки на голову, кончики лезвий слегка коснуться кожи головы и срежут очень короткие волоски. Вы также можете подравнять длинные волоски с помощью бритвы. • Your clippers were carefully examined to ensure that the blades were oiled and aligned before leaving our

Please observe correct battery polarities or the set will not work (see the picture). • Close the battery compartment cover. AC operation • Before the first connecting of the appliance check that voltage indicated on the rating label corresponds the mains voltage in your home. • Plug the corresponding end of cord into the AC socket on the rear of the set. • Insert the plug into power supply. Caution: • When the set is only used with AC or is not used for 2 weeks or more, please remove the

For your safety, it is necessary to refer to the manual. • DANGEROUS VOLTAGE: Uninsulated dangerous voltage that may be of sufficient magnitude to constitute a risk of electrical shock to persons is present within this product enclosure. • CAUTION: To reduce the risk of electric shock, do not remove cover (or back). Prefer servicing to qualified service personnel. POWER SUPPLY BATTERY OPERATION • Set the FUNCTION switch to the TAPE position. • Open the battery compartment cover. • Insert

The display will show "P01". This indicates that the set is now in memory programming mode, at the first memory position. • Select a desired track by using the BACK/TUNE DOWN and NEXT/TUNE UP buttons. • Press the MEM/PROG/P-MODE key again to confirm. • The set will advance to next memory position, the display will show "P02". • Repeat steps described above to enter additional memories into the program if necessary. • After a maximum of 60 songs (or less) have been selected as described abov