Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
►► Auto Lets the BIOS decide whether to enable this function. (Default) ►► Enabled Enables this function to enhance memory compatibility. ►► Disabled Disables this function. & DDR Write Training Allows you to determine whether to fine-tune memory parameters to enhance memory compatibility. ►► Auto Lets the BIOS decide whether to enable this function. (Default) ►► Enabled Enables this function to enhance memory compatibility. ►► Disabled Disables this function. & Channel A/B Driving Settings CMOS Setup Utility-Copyright (C) 1984-2011 Award Software Channel A/B Driving Settings x Driving Strength Profile Auto Item Help M Menu Level ►►► x Data Driving Pull-Up Level Auto x Cmd Driving Pull-Up Level Auto x Ctrl Driving Pull-Up Level Auto x Clk Driving Pull-Up Level Auto x Data Driving Pull-Down Lev Auto x Cmd Driving Pull-Down Lev Auto x Ctrl Driving Pull-Down Lev Auto x Clk Driving Pull-Down Lev Auto ti^^: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help II F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults - 25 - & Driving Strength Profile Options are: Auto (default). & Data Driving Pull-Up Level Options are: Auto (default), +8~-7. & Cmd Driving Pull-Up Level Options are: Auto (default), +8~-7. & Ctrl Driving Pull-Up Level Options are: Auto (default), +8~-7. & Clk Driving Pull-Up Level Options are: Auto (default), +8~-7. & Data Driving Pull-Down Lev Options are: Auto (default), +8~-7. & Cmd Driving Pull-Down Lev Options are: Auto (default), +8~-7. & Ctrl Driving Pull-Down Lev Options are: Auto (default), +8~-7. & Clk Driving Pull-Down Lev Options are: Auto (default), +8~-7. ******** Mother Board Voltage Control ******** >>> CPU & CPU Vcore The default is Auto. & CPU Termination The default is Auto. >>> DRAM DRAM Voltage The default is Auto. - 26 - 2-4 Standard CMOS Features & Date (mm:dd:yy) Sets the system date. & Time (hh:mm:ss) Sets the system time. & IDE Channel 0, 1 Master/Slave ►► IDE Channel 0/1 Master/Slave, Extended IDE Drive Configure your SATA devices by using one of the three methods below: • Auto Lets the BIOS automatically detect SATA devices during the POST. (Default) • None If no SATA devices are used, set this item to None so the system will skip the • Manual Allows you to manually enter the specifications of the hard drive when the hard drive ►► Access Mode Sets the hard drive access mode. (Default: Auto) The following fields display your hard drive specifications. If you wish to enter the parameters manually, refer to the information on the hard drive. & Halt On Allows you to determine whether the system will stop for an error during the POST. Options are: "All Errors,” "No Errors,” "All, But Keyboard” (default), "All, But Diskette,” "All, But Disk/Key." & Memory These fields are read-only and are determined by the BIOS POST detection of the device during the POST for faster system startup. access mode is set to CHS. (For IDE Channel 0 Master/Slave only.) ►► Capacity Approximate capacity of the currently installed hard drive. ►► Cylinder Number of cylinders. ►►Head Number of heads. ►► Precomp Write precompensation cylinder. ► Landing Zone Landing zone. ► Sector Number of sectors. - 27 - 2-5 Advanced BIOS Features CMOS Setup Utility-Copyright (C) 1984-2011 Award Software Advanced BIOS Features ► Hard Disk Boot Priority [Press Enter] Item Help Quick Boot [Disabled] Menu Level ► EFI CD/DVD Boot Option [Auto] First Boot Device [Hard Disk] Second Boot Device [CDROM] Third Boot Device [Legacy LAN] Password Check [Setup] HDD S.M.A.R.T. Capability [Enabled] CPU Multi-Threading (Note) [Enabled] Limit CPUID Max. to 3 (Note) [Disabled] No-Execute Memory Protect (Note) [Enabled] CPU Enhanced Halt (C1E) (Note) [Enabled] C2/C2E State Support (Note) [Disabled] CPU Thermal Monitor 2(TM2) (No te) [Enabled] CPU EIST Function (Note) [Enabled] Virtualization Technology (Note) [Enabled] Delay For HDD (Secs) [0] Backup BIOS Image to HDD [Disabled] Ti^^: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults Hard Disk Boot Priority Specifies the sequence of loading the operating system from the installed hard drives. Quick Boot Enables or disables the quick boot function to speed up the system boot-up process to shorten the waiting time for entering the operating system and to deliver greater efficiency for daily use. (Default: Disabled) EFI CD/DVD Boot Option Set this item to EFI if you want to install the operating system to a hard drive larger than 2.2 TB. Make sure the operating system to be installed supports booting from a GPT partition, such as Windows 7 64-bit and Windows Server 2003 64-bit. Auto lets the BIOS automatically configure this setting depending on the hard drive you install. (Default: Auto) First/Second/Third Boot Device Specifi...