Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
Go to GIGABYTE's website for the latest memory support list.) Audio ♦ Realtek ALC889A codec ♦ High Definition Audio ♦ 2/4/5.1 /7.1 -channel ♦ Support for S/PDIF In/Out ♦ Support for CD In LAN ♦ Realtek 8111B chip (10/100/1000 Mbit) Expansion Slots ♦ 1 x PCI Express x16 slot ♦ 3 x PCI Express x1 slots ♦ 3 x PCI slots Storage Interface ♦ South Bridge: - 6 x SATA 3Gb/s connectors (SATAII0, SATAII1, SATAII2, SATAII3, SATA 114, SATAII5), supporting up to 6 SATA 3Gb/s devices® - 4 x SATA 3Gb/s connectors (SATAII0, SATAII1, SATAII4, SATAII5), supporting up to 4 SATA 3Gb/s devices®® ^ 2) - Support for SATA RAID 0, RAID 1, RAID 5, and RAID 10® ♦ iTE IT8718 chip: - 1 x floppy disk drive connector supporting up to 1 floppy disk drive ® Only for GA-P35C-DS3R. © Only for GA-P35C-DS3. Only for GA-P35C-S3. "*" Only the GA-P35C-DS3R/DS3 adopts All-Solid Capacitor design. GA-P35C-DS3R/DS3/S3 Motherboard - 10 - Storage Interface ♦ GIGABYTE SATA2 chip®: - 1 x IDE connector supporting ATA-133/100/66/33 and up to 2 IDE devices - 2 x SATA 3Gb/s connectors (GSATAII0, GSATAII1), supporting up to 2 SATA 3Gb/s devices) - Support for SATA RAID 0, RAID 1, and JBOD ♦ JMicron 368 chip*®: - 1 x IDE connector supporting ATA-133/100/66/33 and up to 2 IDE devices USB Integrated in the South Bridge Up to 12 USB 2.0/1.1 ports (8 on the back panel, 4 via the USB brackets connected to the internal USB headers) Internal Connectors 1 x 24-pin ATX main power connector 1 x 4-pin ATX 12V power connector 1 x floppy disk drive connector 1 x IDE connector 8 x SATA 3Gb/s connectors® 4 x SATA 3Gb/s connectors®® 1 x CPU fan header 2 x system fan headers 1 x power fan header 1 x front panel header 1 x front panel audio header 1 x CD In connector 1 x S/PDIF In header 1 x S/PDIF Out header 2 x USB 2.0/1.1 headers 1 x parallel port header 1 x serial port header 1 x power LED header 1 x Chassis Intrusion header Back Panel Connectors I/O Controller x PS/2 keyboard port x PS/2 mouse port x coaxial S/PDIF Out connector x optical S/PDIF Out connector 8 x USB 2.0/1.1 ports 1 x RJ-45 port 6 x audio jacks (Center/Subwoofer Speaker Out/Rear Speaker Out/Side Speaker Out/Line In/Line Out/Microphone) iTE IT8718 chip ® Only for GA-P35C-DS3R. Only for GA-P35C-DS3. Only for GA-P35C-S3. - 11 - Hardware Installation English English Hardware Monitor ♦ System voltage detection ♦ CPU/System temperature detection ♦ CPU/System/Power fan speed detection ♦ CPU overheating warning ♦ CPU/System/Power fan fail warning ♦ CPU fan speed control |Note 3) BIOS ♦ 1 x 8 Mbit flash ♦ Use of licensed AWARD BIOS ♦ PnP 1.0a, DMI 2.0, SM BIOS 2.4, ACPI 1.0b Unique Features ♦ Support for @BIOS ♦ Support for Download Center ♦ Support for Q-Flash ♦ Support for EasyTune 4) ♦ Support for Xpress Install ♦ Support for Xpress Recovery2 ♦ Support for Virtual Dual BIOS Bundled Software ♦ Norton Internet Security (OEM version) Operating System ♦ Support for Microsoft® Windows® Vista/XP/2000 ^ 5) Form Factor ♦ ATX Form Factor; 30.5cm x 24.5cm (Note 1) Due to Windows XP 32-bit operating system limitation, when more than 4 GB of physical memory is installed, the actual memory size displayed will be less than 4 GB. (Note 2) To enable hot plug capability for the SATA connectors controlled by the ICH9 South Bridge, you must install Windows Vista (on ICH9, hot plug is supported in Windows Vista only) and configure the SATA connectors for AHCI mode. (Refer to Chapter 2, "BIOS Setup," "Integrated Peripherals," for details on enabling AHCI.) (Note 3) Whether the CPU fan speed control function is supported will depend on the CPU cooler you install. (Note 4) Available functions in Easytune may differ by motherboard model. (Note 5) Due to chipset limitation, Intel ICH9R RAID driver does not support Windows 2000 operating system. GA-P35C-DS3R/DS3/S3 Motherboard - 12 - 1-3 Installing the CPU and CPU Cooler A Read the following guidelines before you begin to install the CPU: • Make sure that the motherboard supports the CPU. (Go to GIGABYTE's website for the latest CPU support list.) • Always turn off the computer and unplug the power cord from the power outlet before installing the CPU to prevent hardware damage. • Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may locate the notches on both sides of the CPU and alignment keys on the CPU socket.) • Apply an even and thin layer of thermal grease on the surface of the CPU. • Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage of the CPU may occur. • Set the CPU host frequency in accordance with the CPU specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the standard requirements for the peripherals. If you wish to set the frequency beyond the standard specifications, please do so according to your hardware specificatio...