Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
2 (1) Installing SATA hard drive(s) in your system ......................................................................... 2 (2) Configuring SATA controller mode and boot sequence in BIOS Setup .................................. 3 (3) Configuring SATA hard drives in RAID BIOS .......................................................................... 6 (4) Making a SATA controller driver disk ................................................................................... 10 (5) Installing SATA controller driver during OS installation ......................................................... 12 Configuring SATA Hard Drive(s) (Controller: Silicon Image Sil3132) To configure SATA hard drive(s), follow the steps below: (1) Install SATA hard drive(s) in your system. (2) Configure SATA controller mode and boot sequence in BIOS Setup. (3)* Configure RAID set in RAID BIOS. (4) Make a floppy disk containing the SATA controller driver. (5) Install the SATA controller driver during OS installation. Before you begin Plea se prep are: (a) SATA hard drives (to ensure optimal performance, it is recommended that you use hard drives with identical model and capacity). (b) An empty formatted floppy disk. (c) Wind ows XP /2000 s etup d isk. (d) Driver CD for your motherboard. (1) Installing SATA hard drive(s) in your system Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA port(s) on the motherboard. If there are more than one SATA controller on your motherboard, you may refer to the motherboard user's manual to identify the SATA controller for the connector. Then connect the po wer connec tor from y our power supply to the hard d rive. "*" Skip this step if you do not want to create RAID array on the SATA controller. SATA Hard Drive Configurations (Sil3132) -2 (2) Configuring SATA controller mode and boot sequence in BIOS Setup Assure that the SATA controller is enabled in system BIOS Setup. Step 1: Turn on your computer and press Del to enter BIOS Setup during POST (Power-On Self Test). In BIOS Setup menu, go to Integrated Peripherals and assure that Onboard H/W SATA (Figure 1) is enabled. If you wish to create a RAID array, set H/W SATA Function to RAID. For non-RAID hard disk, please set it to BASE. CMOS Setup Utility Copyright (C) 1984 2005 Award Software Integrated Peripherals On-Chip Primary PCI IDE [Enabled] On-Chip Secondary PCI IDE [Enabled] SATA RAID/AHCI Mode [RAID] x On-Chip SATA Mode Auto x PATA IDE Set to Ch.1 Master/Slave SATA Port 0/2 Set to Ch.2 Master/Slave SATA Port 1/3 Set to Ch.3 Master/Slave USB Controller [Enabled] USB 2.0 Controller [Enabled] USB Keyboard Support [Disabled] USB Mouse Support [Disabled] Azalia Codec [Auto] Onboard H/W 1394 [Enabled] Onboard H/W SATA [Enabled] H/W SATA Function [RAID] Onboard H/W GigaRAID [Enabled] GigaRAID Function [RAID] Onboard H/W LAN1 [Enabled] Onboard H/W LAN2 [Enabled] higf: Move Enter: Select +/ /PU/P D: Value F10: Save ESC: Exit F1: General Help F3: Language F5: Previous Values F6: Fail Safe Defaults F7: Optimized Defaults Item Help Menu Level} If a hard disk controller card is used, set at Disabled. [Enabled] Enable on-chip IDE Port. [Disabled] Disable on-chip IDE Port. Figu re 1 Th e B IOS Se tu p m enu s d esc rib ed in th is sec tio n m ay not s how th e e xac t s ett in gs for yo ur motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you have a nd the BIOS versio n . -3 -SATA Hard Drive Configurations (Sil3132) Step 2: If you do not create RAID, select Hard Disk Boot Priority under the Advanced BIOS Features menu. In the Hard Disk Boot Priority submenu, select the model of the SATA hard drive onto which you wish to install Microsoft Windows 2000/XP. You should see a screen similar to Figure 2 below. CMOS Setup Utility Copyright (C) 1984 2005 Award Software Hard Disk Boot Priority 1. SCSI-0 : 05:00-0 ST3120026AS 2. SCSI-1 : 05:00-1 ST3120026AS 3. Bootable Add-in Cards hi: Move PU/PD/+/-: Change Priority F10: Save ESC: Exit Item Help Menu Level }} Use