Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
-11 - Hardware Installation English 1-3 Installation of the CPU and CPU Cooler Before installing the CPU, please comply with the following conditions: 1. Please make sure that the motherboard supports the CPU. 2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong direction, the CPU will not insert properly. If this occurs, please change the insert direction of the CPU. 3. Please add an even layer of heat sink paste between the CPU and CPU cooler. 4. Please make sure the CPU cooler is installed on the CPU prior to system use, otherwise overheating and permanent damage of the CPU may occur. 5. Please set the CPU host frequency in accordance with the processor specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the required standards for the peripherals. If you wish to set the frequency beyond the proper specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc. HT functionality requirement content : Enabling the functionality of Hyper-Threading Technology for your computer system requires all of the following platform components: - CPU: An Intel® Pentium 4 Processor with HT Technology - Chipset: An Intel® Chipset that supports HT Technology - BIOS: A BIOS that supports HT Technology and has it enabled - OS: An operation system that has optimizations for HT Technology 1-3-1 Installation of the CPU Metal Lever Fig. 1 Fig. 2 Gently lift the metal Remove the plastic lever located on the covering on the CPU CPU socket to the socket. upright position. Fig. 3 Fig. 4 Notice the small gold Once the CPU is colored triangle properly inserted, located on the edge of please replace the the CPU socket. load plate and push the Align the indented metal lever back into its original position. corner of the CPU with the triangle and gently insert the CPU into position. (Grasping the CPU firmly between your thumb and forefinger, care fully place it into the socket in a straight and down wards motion. Avoid twisting or bending motions that might cause damage to the CPU during installation.) GA-945PL-(D)S3 (rev. 2.0) Motherboard -12 1-3-2 Installation of the Cooler Male Push Pin The top of Female Push Pin Female Push Pin Fig.1 Fig. 2 Please apply an even layer of CPU cooler paste (Turning the push pin along the direction of arrow is to on the surface of the installed CPU. remove the CPU cooler, on the contrary, is to install.) Please note the direction of arrow sign on the male push pin doesn't face inwards before installation. (This instruction is only for Intel boxed fan) Fig. 3 Fig. 4 Place the CPU cooler atop the CPU and make Please make sure the Male and Female push pin sure the push pins aim to the pin hole on the are joined closely. (for detailed installation motherboard.Pressing down the push pins instructions, please refer to the CPU cooler instal- diagonally. lation section of the user manual) Fig. 6 Fig. 5 Finally, please attach the power connector of the Please check the back of motherboard after CPU cooler to the CPU fan header located on the installing. If the push pin is inserted as the picture, motherboard. the installation is complete. The CPU cooler may adhere to the CPU as a result of hardening of the heat paste. To prevent such an occurrence, it is suggested that either thermal tape rather than heat paste be used for heat dissipation or using extreme care when removing the CPU cooler. English -13 - Hardware Installation GA-945PL-(D)S3 (rev. 2.0) Motherboard - 14 - English Before installing the memory modules, please comply with the following conditions: 1. Please make sure that the memory used is supported by the motherboard. It is recommended that memory of similar capacity, specifications and brand be used. 2. Before installing or removing memory modules, please make sure that the computer power is switched off to prevent hardware damage. 3. Memory modules have a foolproof insertion design. A memory module can be installed in only one direction. If you are unable to insert the module, please switch the direction. 1-4 Installation of Memory The motherboard supports DDRII memory modules, whereby BIOS will automatically detect memory capacity and specifications. Memory modules are designed so that they can be inserted only in one direction. The memory capacity used can differ with each slot. Notch DDRII Fig.1 The DIMM socket has a notch, so the DIMM memory module can only fit in one direction. Insert the DIMM memory module vertically into the DIMM socket. Then push it down. Fig.2 Close the plastic clip at both edges of the DIMM sockets to lock the DIMM module. Reverse the installation steps when you wish to remove the DIMM module. English Dual Channel Memory Configuration GA-945PL-DS3/GA-945PL-S3 supports the Dual Channel Technology. After operating the Dual Channel Technology, the bandwidth of Memory Bus will add double. GA-9...