Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Tarjetas Madre - GA-8I945GZME-RH (10.57 mb)
Tarjetas Madre - GA-8I945GZME-RH (16.33 mb)
Resumen del manual
The black connector wire is the ground wire (GND). Remember to connect the CPU/system fan cable to the CPU_FAN/SYS_FAN connector to prevent CPU damage or system hanging caused by overheating. Pin No. Definition 1 GND 2 +12V 3 Sense 4 Speed Control 1 (Only for CPU_FAN) CPU_FAN SYS_FAN 1 5) IDE (IDE Connector) An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other as Slave (for information on settings, please refer to the instructions located on the IDE device). Before attaching the IDE cable, please take note of the foolproof groove in the IDE connector. 2 40 1 39 - 21 - Hardware Installation English 6) FDD (FDD Connector) The FDD connector is used to connect the FDD cable while the other end of the cable connects to the FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB. Before attaching the FDD cable, please take note of the foolproof groove in the FDD connector. 2 1 34 33 Pin No. Definition 1 GND 2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND 7) SATAII0 / SATAII1 / SATAII2 / SATAII3 (SATA 3Gb/s Connectors) SATA 3Gb/s can provide up to 300MB/s transfer rate. Please refer to the BIOS setting for the SATA 3Gb/s and install the proper driver in order to work properly. 1 7 7 1 SATAII0 SATAII1 1 7 7 1 SATAII2 SATAII3 GA-8I945GZME-RH Motherboard - 22 - English 8) PWR_LED The PWR_LED connector is connected with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode. Pin No. Definition 1 MPD+ 2 MPD- 3 MPD- 1 9) F_AUDIO (Front Audio Connector) This connector supports either HD (High Definition) or AC97 front panel audio module. If you wish to use the front audio function, connect the front panel audio module to this connector. Check the pin assignments carefully while you connect the front panel audio module. Incorrect connection between the module and connector will make the audio device unable to work or even damage it. For optional front panel audio module, please contact your chassis manufacturer. By default, the audio driver is configured to support HD Audio. To connect an AC97 front panel audio module to this connector, please refer to the instructions on Page 65 about the software settings. HD Audio: AC'97 Audio: 2 1 10 9 Pin No. Definition 1 MIC 2 GND 3 MIC Power 4 NC 5 Line Out (R) 6 NC 7 NC 8 No Pin 9 Line Out (L) 10 NC Pin No. Definition 1 MIC2_L 2 GND 3 MIC2_R 4 -ACZ_DET 5 LINE2_R 6 FSENSE1 7 FAUDIO_JD 8 No Pin 9 LINE2_L 10 FSENSE2 - 23 - Hardware Installation English 10) F_PANEL (Front Panel Jumper) Please connect the power LED, PC speaker, reset switch and power switch etc of your chassis front panel to the F_PANEL connector according to the pin assignment below. 1 2 19 20 HDHD+ RES+ RESNC IDE Hard Disk Active LED Reset Switch SPEAKMSGMSG+ PWPW+ Message LED/ Power/ Sleep LED Speaker Connector SPEAK+ Power Switch HD (IDE Hard Disk Active LED) Pin 1: LED anode(+) Pin 2: LED cathode(-) SPEAK (Speaker Connector) Pin 1: Power Pin 2- Pin 3: NC Pin 4: Data(-) RES (Reset Switch) Open: Normal Close: Reset Hardware System PW (Power Switch) Open: Normal Close: Power On/Off MSG (Message LED/Power/Sleep LED) Pin 1: LED anode(+) Pin 2: LED cathode(-) NC NC GA-8I945GZME-RH Motherboard - 24 - English 11) CD_IN (CD In Connector) Connect CD-ROM or DVD-ROM audio out to the connector. Pin No. Definition 1 CD-L 2 GND 3 GND 4 CD-R 1 12) SPDIF_IO (SPDIF In/Out) The SPDIF output is capable of providing digital audio to external speakers or compressed AC3 data to an external Dolby Digital Decoder. Use this feature only when your stereo system has digital input function. Use SPDIF IN feature only when your device has digital output function. Be careful with the polarity of the SPDIF_IO connector. Check the pin assignment carefully while you connect the SPDIF cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional SPDIF cable, please contact your local dealer. Pin No. Definition 1 Power 2 No Pin 3 SPDIF 4 SPDIFI 5 GND 6 GND 1 6 2 5 - 25 - Hardware Installation English 14) F_USB1/F_USB2 (Front USB Connectors) Be careful with the polarity of the front USB connector. Check the pin assignment carefully while you connect the front USB cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional front USB cable, please contact your local dealer. 10 2 9 1 Pin No. Definition 1 Power (5V) 2 Power (5V) 3 USB DX- 4 USB Dy- 5 USB DX+ 6 USB Dy+ 7 GND 8 GND 9 No Pin 10 NC 13) HDA_SUR (Surround Center Connector) Please connect the connector of the Surround Kit module to this connector. Pin No. Definition 1 LEF_P 2 SURR_RR 3 CEN_P 4 SURR_LL 5 CEN_JD 6 SURR_JD 7 GND 8 -SUR_...