Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
2 (1) Installing IDE hard drive(s) in your system ................................................................................ 2 (2) Configuring VT6410 IDE controller mode and boot sequence in BIOS Setup ....................... 3 (3) Configuring RAID set in RAID BIOS ............................................................................................. 5 (4) Making a IDE RAID controller driver disk .................................................................................. 10 (5) Installing IDE RAID controller driver during OS installation ..................................................... 12 Ac Configuring IDE RAID Hard Drive(s) (Controller: VIA VT6410) Ae ¤¤ To set up IDE RAID hard drive(s), you have to follow the steps below: ¤a (1) Install IDE hard drive(s) in your computer. (2) Configure VT6410 IDE controller mode and boot sequence in BIOS Setup. (3)* Configure RAID set in RAID BIOS. (4) Make a floppy disk containing the IDE RAID controller driver (5) Install the IDE RAID controller driver during OS installation. Before you begin Please prepare: (a) Two IDE hard drives (to ensure optimal performance, it is recommended that you use two hard drives with identical model and capacity). If you do not plan to create RAID with the VT6410 controller, you may prepare only one hard drive. (b) An empty formatted floppy disk. (c) Windows XP/2000 setup disk. (d) Driver CD for your motherboard. (1) Installing IDE hard drive(s) in your system Attach one end of the IDE cable to the rear of the IDE hard drive and the other end to IDE port(s) controlled by the VT6410 RAID controller on the motherboard. (To ensure that your IDE CD-ROM can work properly, please connect it to the IDE1 port (controlled by the Southbridge) and connect your hard drives to IDE2/IDE3 ports ). Then connect the power connector from your power supply to the hard drive(s). "*" Skip this step if you do not want to create RAID.array on the IDE controller VIA VT6410 IDE RAID Drives Configuration -2 (2) Configuring VT6410 IDE controller mode and boot sequence in BIOS Setup You have to make sure whether the VT6410 IDE controller are configured correctly in system BIOS Setup and set BIOS boot sequence for the IDE RAID hard drive(s). Step 1: Turn on your computer and press the Del key to enter BIOS Setup during POST (Power-On Self Test). To enable the VT6410 IDE controller, please select Onboard H/W RAID under the Integrated Peripherals menu and then press ENTER. Make sure the Onboard H/W RAID item is set to Enabled (Enabled by default) (Figure 1). If you set this option to Disabled, the VT6410 IDE controller will be disabled and will not support any devices. CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Integrated Peripherals On-Chip Primary PCI IDE SATA RAID/AHCI Mode x On-Chip SATA Mode x PATA IDE Set to SATA Port 0/2 Set to SATA Port 1/3 Set to USB Controller USB 2.0 Controller USB Keyboard Support USB Mouse Support Azalia Codec Onboard H/W RAID Onboard H/W 1394 Onboard H/W LAN1 Onboard H/W LAN2 Onboard LAN1 Boot ROM Onboard LAN2 Boot ROM Onboard Serial Port 1 Onboard IrDA Port [Enabled] [RAID] Auto Ch.1 Master/Slave Ch.2 Master/Slave Ch.3 Master/Slave [Enabled] [Enabled] [Disabled] [Disabled] [Auto] [Enabled] [Enabled] [Enabled] [Enabled] [Disabled] [Disabled] [3F8/IRQ4] [2F8/IRQ] Item Help Menu Level• ........: Move Enter: Select F5: Previous Values+/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F6: Fail-Safe Defaults F7: Optimized Defaults Figure 1 -3 -VIA VT6410 IDE RAID Drives Configuration Ac Ae ¤¤ Step 2: Select Hard Disk Boot Priority under the Advanced BIOS Features menu and then choose the model of the IDE hard drive onto which you want to install Microsoft Windows 2000/XP (Figure 2). CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Hard Disk Boot Priority ¤a 1. SCSI-0 : Maxtor 6E030L0 2. SCSI-1 : Maxtor 6E030L0 3. Bootable Add-in Cards ....: Move PU/PD/+/-: Change Priority F10: Save ESC: Exit Item Help Menu Level ..• Use <..> or <..> to select a device, then press <+> to move it up, or <-> to move it down the list. Press