Votos - 1, Puntuación media: 1
(
)
)
|
Otros manuales para este modelo:
Tarjetas Madre - GA-8IP900 (2.64 mb)
Tarjetas Madre - GA-8IP900 (4.96 mb)
Tarjetas Madre - GA-8IP900 (5.77 mb)
Tarjetas Madre - GA-8IP900 (217.21 kb)
Resumen del manual
gAMI BIOS Beep Codes *Computer gives 1 short beep when system boots successfully. *Except for beep code 8, these codes are always fatal. 1 beep Refresh failure 2 beeps Parity error 3 beeps Base 64K memory failure 4 beeps Timer not operational 5 beeps Processor error 6 beeps 8042 -gate A20 failure 7 beeps Processor exception interrupt error 8 beeps Display memory read/write failure 9 beeps ROM checksum error 10 beeps CMOS shutdown register read/write error 11 beeps Cache memory bad • AWARD BIOS Beep Codes 1 short: System boots successfully 2 short: CMOS setting error 1 long 1 short: DRAM or M/B error 1 long 2 short: Monitor or display card error 1 long 3 short: Keyboard error 1 long 9 short: BIOS ROM error Continuous long beeps: DRAM error Continuous short beeps: Power error Question 11: How to set in the BIOS in order to bootup from SATA HDDs by either RAID or ATA mode? Answer: Please set in the BIOS as follow: 1. Advanced BIOS features--> SATA/RAID/SCSI boot order: "SATA" 2. Advanced BIOS features--> First boot device: "SCSI" 3. Integrated Peripherals--> Onboard H/W Serial ATA: "enable" Then it depends on the SATA mode that you need to set "RAID" to RAID mode or "BASE" to normal ATA mode in the item named Serial ATA function. English -87 -Appendix EnglishEnglish Question 12:For the M/B which have RAID function, how to set in the BIOS in order to bootup from IDE3, 4 by either RAID or ATA mode? Answer:Please set in the BIOS as follow: 1. Advanced BIOS features-->(SATA)/RAID/SCSI boot order: "SATA" 2. Advanced BIOS features--> First boot device: "SCSI" 3. Integrated Peripherals--> Onboard H/W ATA/RAID: "enable" Then it depends on the RAID mode that you need to set "RAID" to RAID mode or "ATA" to normal ATA mode in the item named RAID controller function. Question 13:How to set in the BIOS to bootup from the IDE/ SCSI/ RAID card ? Answer:Please set in the BIOS as follow: 1. Advanced BIOS features-->(SATA)/RAID/SCSI boot order: "SCSI" 2. Advanced BIOS features--> First boot device: "SCSI" Then it depends on the mode(RAID or ATA) that you need to set in RAID/ SCSI BIOS. GA-8IP900(-L) Motherboard -88 Troubleshooting If you encounter any trouble during boot up, please follow the troubleshooting procedures . Turn off the power and unplug the AC power cable, then remove all of the add-on cards and cables from motherboard. START Yes Please make sure motherboard & chassis are not short ? No Failure has been excluded. Please isolate the short pin. A Please make sure all jumper settings (such as CPU system bus speed, frequency ratio, voltage and etc.) are set properly. Failure has been excluded. Check if the CPU cooling fan attached to CPU properly. ls CPU cooling fan power connected to CPU_FAN properly? Plug the CPU cooling fan power in the CPU fan connector. Plug in the AC power connect or. Check if the memory install properly into the DIMM slot. Yes No Yes Insert and push the memory module vertically into the DIMM slot. Insert the VGA card. Then plug in ATX power cable and turn on the system. No No Yes Failure has been excluded. Failure has been excluded. Make sure the jumper setting are correct. English -89 -Appendix EnglishEnglish Is memory LED on and CPU fan running? Yes A Check if there is display. Yes Check if keyboard is working properly. Yes Yes Turn off the system and re-connect the IDE cable. Check if the system can reboot successfully. Perhaps your VGA card / VGA slot or monitor is defect ive. Turn off the system. Reboot after keyboard and mouse have been plugged in. It is possible that your keyboard or keyboard connect or is defective. Press to enter BIOS setup. Choose "Load Optimized Defaults" and save then exit setup. No The problem could be caused by power supply, CPU, memory or CPU/ memory socket itself. Failure has been excluded. No Failure has been excluded. No Failure has been excluded. No The problem was probably caused by the IDE device / connector or cable. Reinstall Windows OS, and reinstall add-on cards and cables. Then try to reboot the system. END Failure has been excluded. If the above procedure unable to solve your problem, please contact with your local retailer or national distributor for help. Or, you could submit your question to the service mail via Gigabyte website technical support zone (The appropriate response will be provided ASAP. GA-8IP900(-L) Motherboard -90 Technical Support/RMA Sheet Customer/Country: Company: Phone No.: Contact Person: E-mail Add. : Model name/Lot Number: PCB revision: BIOS version: O.S./A.S.: Hardware Mfs. Model name Size: Driver/Utility: Configuration CPU Memory Brand Video Card Audio Card HDD CD-ROM / DVD-ROM Modem Network AMR / CNR Keyboard Mouse Power supply Other Device Problem Description: & & English -91 -Appendix EnglishEnglish Acronyms Acronyms Meaning ACPI Advanced Configuration and Power Interface APM Advanced Power Management AGP Accelerated Graphics Port AMR Audio Modem Riser ACR Advanced Communications Riser ...