Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
• ..........First / Second / Third Boot Device ..Floppy Select your boot device priority by Floppy. ..LS120 Select your boot device priority by LS120. ..HDD-0~3 Select your boot device priority by HDD-0~3. ..SCSI Select your boot device priority by SCSI. ..CDROM Select your boot device priority by CDROM. ..ZIP Select your boot device priority by ZIP. ..USB-FDD Select your boot device priority by USB-FDD. ..USB-ZIP Select your boot device priority by USB-ZIP. ..USB-CDROM Select your boot device priority by USB-CDROM. ..USB-HDD Select your boot device priority by USB-HDD. ..LAN Select your boot device priority by LAN. ..Disabled Select your boot device priority by Disabled. English -35-BIOS Setup English English • ..........Boot Up Floppy Seek During POST, BIOS will determine the floppy disk drive installed is 40 or 80 tracks. 360 K type is 40 tracks 720 K, 1.2 M and 1.44 M are all 80 tracks. ..Enabled BIOS searches for floppy disk drive to determine it is 40 or 80 tracks. Note that BIOS can not tell from 720 K, 1.2 M or 1.44 M drive type as they are all 80tracks. ..Disabled BIOS will not search for the type of floppy disk drive by track number. Note that there will not be any warning message if the drive installed is 360 K. (Default value) • ..........Password Check This category allows you to limit access to the system and Setup, or just to Setup. ..System The user must enter correct password in order to access the system and/or BIOS setup. ..Setup The user must enter correct password in order to access BIOS setup utility. (Default value) • ..........CPU Hyper-Threading ..Enabled Enables CPU Hyper Threading Feature. Please note that this feature is only working for operating system with multi processors mode supported. (Default value) ..Disabled Disables CPU Hyper Threading. • ..........Init Display First ..Onboard AGP Set Init Display First to onboard/AGP. (Default value) ..PCI Set Init Display First to PCI. • ..........Graphics Aperture Size ..128MB Set Graphics Aperture Size to 128MB. (Default value) ..Disabled Disable this function. • ..........Graphics Share Memory ..8MB Set Graphics Share Memory to 8MB. (Default value) ..1MB Set Graphics Share Memory to 1MB. GA-8VD667 Motherboard -36 Integrated Peripherals CMOS Setup Utility-Copyright (C) 1984-2002 Award Software Integrated Peripherals On-Chip Primary PCI IDE On-Chip Secondary PCI IDE IDE1 Conductor Cable IDE2 Conductor Cable USB Controller USB Keyboard Support USB Mouse Support AC97 Audio Onboard H/W LAN Onboard LAN Boot ROM Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select x UR2 Duplex Mode Onboard Parallel Port Parallel Port Mode x ECP Mode Use DMA Game Port Address Midi Port Address Midi Port IRQ Enabled Enabled Auto Auto Enabled Disabled Disabled Auto Enabled Disabled 3F8/IRQ4 2F8/IRQ3 Normal Half 378/IRQ7 SPP 3 201 330 10 Item Help Menu Level • Ifa hard disk controller card is used, set at Disable [Enabled] Enable onboard IDE PORT [Disabled] Disable onboard IDE PORT • ........: Move Enter:Select F5:Previous V alues +/-/PU/PD:V alue F10:Save ESC:Exit F1:General Help F6:Fail-Safe Defaults F7:Optimized Defaults Figure 4: Integrated Peripherals English -37 -BIOS Setup EnglishEnglish • ..........On-Chip Primary PCI IDE ..When enabled, allows you to use the onboard primary PCI IDE. If a hard disk controller card is used, set at Disabled. ..Enabled ..Disabled • ..........On-Chip Secondary PCI IDE ..When enabled, allows you to use the onboard secondary PCI IDE. If a hard disk controller card is used, set at Disabled. ..Enabled ..Disabled • ..........IDE1 Conductor Cable ..Auto ..ATA66/100 ..ATA33 • ..........IDE2 Conductor Cable ..Auto ..ATA66/100 ..ATA33 • ..........USB Controller ..Enabled ..Disabled • ..........USB Keyboard Support ..When a USB keyboard is installed, please set at Enabled. ..Enabled ..Disabled Enable onboard 1st channel IDE port. (Default value) Disable onboard 1st channel IDE port. Enable onboard 2nd channel IDE port. (Default value) Disable onboard 2nd channel IDE port. W ill be automatically detected by BIOS. (Default Value) Set IDE1 Conductor Cable to ATA66/100 (Please make sure your IDE device and cable is compatible with ATA66/100). Set IDE1 Conductor Cable to ATA33 (Please make sure your IDE device and cable is compatible with ATA33). W ill be automatically detected by BIOS. (Default Value) Set IDE2 Conductor Cable to ATA66/100 (Please make sure your IDE device and cable is compatible with ATA66/100). Set IDE2 Conductor Cable to ATA33 (Please make sure your IDE device and cable is compatible with ATA33). ..Disable this option if you are not using the onboard USB feature. Enable USB Controller. (Default value) Disable USB Controller. Enable USB Keyboard Support. Disable USB Keyboard Support. (Default value) GA-8VD667 Motherboard -38 • ..........USB Mouse Support ..Enabled Enable USB Mouse Support. ..Disabled Disable USB Mouse Support. (Default value) • ..........AC97 Audio ..Auto BIOS will automatically detect onboar...